Runco DTV-1200 owner manual Undo Green Convergence Mid, Undo Focus to Midposition

Page 67

Undo Green Convergence Mid

What can be done?

'Undo Green convergence mid' is displayed in the Set Midposition menu instead of 'Green convergence mid' when the latter is pressed. Only available when the projector is equipped with green convergence adjustmentes.

How to undo?

1.Push the cursor key or to highlight 'Undo Green Convergence Mid' (menu 1).

2.Press ENTER undo.

SET TO MIDPOSITION

R&B CONVERGENCE MID

UNDO GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 1

Focus to Midposition

What can be done?

The focus settings can be set to midposition.

How to set the Focus settings to midposition?

1.Push the cursor key or to highlight 'Focus to Midposition' (menu 1).

2.Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3.Press ENTER to confirm. Press EXIT to cancel the procedure to set the focus settings to their midposition.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or
then <ENTER>
<EXIT> to return.	menu 1

FOCUS TO MIDPOSITION
!
Focus settings
in current block
will be overwritten!
<ENTER> to confirm	menu 2
<EXIT> to cancel	menu 2

Undo Focus to Midposition

What can be done?

'Undo Focus to Midposition' is displayed in the Set Midposition menu instead of 'Focus to midposition' when the latter is pressed. As long the projector is running on the same source (= same adjustment block), undo the focus to midposition is possible.

How to undo the Focus to midposition?

1.Push the cursor key or to highlight 'Undo Focus to Midposition' (menu 1).

2.Press ENTER undo.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

UNDO FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID DIG HOR LINEARITY MID ASTIGMATISM MIDPOSITION ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 1

65

Image 67

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to ProjectorSource No Projector Input Remote Button No Source ConnectionsRGB Source with Composite Sync to Input 4/5 RGB Source to InputInput Select Input Component Source to Input 4/5 RGB Source with Tri-level Sync to Input 4/5RS-232 Connection Getting Started Remote Control & Local KeypadAudio controls not used Projector Warm UP Stationary Image WarningFront of projector Remote Commands to the ProjectorProjector Address Input Selection via the Remote Contrast Control Brightness ControlColor Saturation Control Not used on the DTV-1200 Adjustment Mode Start UP of the Adjustment ModeMain Menu Main MenuImage Control Color AdjustFormat Select Compose Eye-Q Touch Up Eye-Q ControlEye-Q Auto Converge Main Menu Adjustment ModeService Menus Entering the Service MenusEnter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern VGA Internal Cross Hatch PatternPicture Tuning Random Access Adjustment Mode Selection MenuPicture Tuning Random Access Adjustment ModeColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalancePicture Tuning Sync Fast/Slow AdjustmentsColor Balance Peaking Clamp TuningPiture Tuning PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustments Random Access Adjustment ModePhase Raster Shift AdjustmentsCoarse Shift Left-Right East-West AdjustmentsForbidden Area Projected Raster CRT Faceplate Border PhosphorLEFT-RIGHT Left Side Correction Left Side CorrectionWhat can be done? Start upTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOMSize Horizontal Size AdjustmentsLinearity V Size Vertical Linearity AdjustmentsLinearity Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceMidpoint FocusingFocusing FocusingBottom TOPLeft Color Select Color SelectRight Blue on SourceService Mode Service ModeService Mode Random Access InstallationText ON/OFF Projector SetupSoftware version Configuration IdentificationRUN Time Run TimeProjector SET-UP IdentificationChange Password Change PasswordChange Password PasswordBaud Rate Change Projector AddressChange Baud Rate Projector SET-UP Projector AddressWarm Up On/Off Projector Warm UpProjector Warm UP Projector Warm Up Time Warm Up FrequencyProjector Warm UP Common Address Power Up ModeMemory Management Copy ModeMemory Management Copy a BlockDeletion of All Blocks Delete ModeDeletion of Blocks Deleting Block by BlockSET to Midposition Set to MidpositionCovergence Mid Delete ALL BlocksGreen Convergence MID Undo R & B Convergence MidConvergence MID SET to MidpositionFocus to Midposition Undo Green Convergence MidUndo Focus to Midposition To Midposition North-South Settings to MidpositionEast-West to Midposition Undo East-West to MidpositionDIG Vert Linearity MID Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition Undo Digital Vertical Linearity to MidpositionDIG HOR Linearity MID Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition Astigmatism to MidpositionUndo All Settings to Midposition All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Green Dynamic AstigmatismCRT RUN in Cycle Common SettingsGamma Corrections CRT Run In CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Menu Position Flyback Turnover PointFlyback Turnover Point Decoder 12C DiagnosticsVoltage Diagnostics I2C DiagnosticsVoltage Diagnostics Projector DiagnosticsProjector Diagnostics Projector DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Block Header Example of Block Header Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Source NumbersSource input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR ConfigurationFront View DimensionsBottom View Side ViewSpecifications Page RUMA-009450 rev