Runco DTV-1200 owner manual Undo Astigmatism to Midposition, All Settings to Midposition

Page 71

Undo Astigmatism to Midposition

What can be done?

'Undo Astigmatism midposition' is displayed in the Set Midposition menu instead of 'Astigmatism midposition' when the latter is pressed. The settings for the astigmatism can be returned to previous installed settings as long the projector is playing on the same source ( = same adjustment block).

How to undo the Astigmatism settings to midposition?

1.Push the cursor key or to highlight 'Undo Astigmatism Midposition' (menu 1).

2.Press ENTER undo.

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID DIG HOR LINEARITY MID

UNDO ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

All Settings to Midposition

What can be done?

All adjustment settings can be set to midposition.

How to set to midposition?

1.Push the cursor key or to highlight 'All Settings to Midposition' (menu 1).

2.Press ENTER to select. A confirmation menu will be displayed first (menu 2).

3.Press ENTER to confirm. Press EXIT to cancel the operation 'set all settings to their midposition'.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

 

then <ENTER>

 

<EXIT> to return.

menu 1

ALL SETTINGS TO MIDPOSITION

!

Astigmatism settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

menu 2

Undo All Settings to Midposition

What can be done?

'Undo all settings to Midposition' is displayed in the Memory management menu instead of 'All settings to midposition' when the latter is pressed.

An undo is possible as long as the projector is running on the same source (= same adjustment block) even when some adjustments as geometry or conver- gence are already readjusted. When undo is pressed all settings are reset to the previous settings.

How to cancel 'Set to midposition'?

When "All settings to midpos" is selected, all settings are set to their midposition. To cancel this action:

1.Push the cursor key or to highlight 'Undo All Settings to midpos' (menu 1).

2.Press ENTER to cancel the set to midposition action.

Press EXIT to cancel the procedure 'undo set to midposition'.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

UNDO ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 1

69

Page 70 Page 72
Image 71
Page 70 Page 72
Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to ProjectorSource No Projector Input Remote Button No Source ConnectionsInput Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Getting Started Remote Control & Local KeypadAudio controls not used Projector Warm UP Stationary Image WarningFront of projector Remote Commands to the ProjectorProjector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Adjustment Mode Start UP of the Adjustment ModeMain Menu Main MenuImage Control Color AdjustFormat Select Compose Eye-Q Touch Up Eye-Q ControlEye-Q Auto Converge Main Menu Adjustment ModeService Menus Entering the Service MenusEnter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern VGA Internal Cross Hatch PatternPicture Tuning Random Access Adjustment Mode Selection MenuPicture Tuning Random Access Adjustment ModeColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalanceColor Balance Sync Fast/Slow AdjustmentsPicture Tuning Peaking Clamp TuningPiture Tuning PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustments Random Access Adjustment ModePhase Raster Shift AdjustmentsCoarse Shift Left-Right East-West AdjustmentsForbidden Area Projected Raster CRT Faceplate Border PhosphorLEFT-RIGHT Left Side Correction Left Side CorrectionWhat can be done? Start upTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOMSize Horizontal Size AdjustmentsLinearity Vertical Linearity AdjustmentsLinearity V Size Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceMidpoint FocusingFocusing FocusingLeft TOPBottom Color Select Color SelectRight Blue on SourceService Mode Service ModeService Mode Random Access InstallationText ON/OFF Projector SetupSoftware version Configuration IdentificationRUN Time Run TimeProjector SET-UP IdentificationChange Password Change PasswordChange Password PasswordBaud Rate Change Projector AddressChange Baud Rate Projector SET-UP Projector AddressProjector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Common Address Power Up ModeMemory Management Copy ModeMemory Management Copy a BlockDeletion of All Blocks Delete ModeDeletion of Blocks Deleting Block by BlockSET to Midposition Set to MidpositionCovergence Mid Delete ALL BlocksGreen Convergence MID Undo R & B Convergence MidConvergence MID SET to MidpositionUndo Focus to Midposition Undo Green Convergence MidFocus to Midposition To Midposition North-South Settings to MidpositionEast-West to Midposition Undo East-West to MidpositionDIG Vert Linearity MID Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition Undo Digital Vertical Linearity to MidpositionDIG HOR Linearity MID Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition Astigmatism to MidpositionUndo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Green Dynamic AstigmatismCRT RUN in Cycle Common SettingsGamma Corrections CRT Run In CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position Decoder 12C DiagnosticsVoltage Diagnostics I2C DiagnosticsVoltage Diagnostics Projector DiagnosticsProjector Diagnostics Projector DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Block Header Example of Block Header Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Source NumbersSource input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR ConfigurationFront View DimensionsBottom View Side ViewSpecifications Page RUMA-009450 rev
Top Page Image Contents