Runco DTV-1200 owner manual Programmable Function Keys, Phase Raster Shift

Page 80

PROGRAMMABLE FUNCTION KEYS

Programmable Function Keys

What can be done with these keys?

The five function keys on top of the remote control can be programmed as short cut keys (quick access) to almost any adjustment function. See list futher in this chapter.

How can a Function Key be programmed?

A function key can only be programmed when in the service menus.

Perform the following:

1.Scroll through the menus until the desired function is on the menu.

2.Select this function by pushing the cursor keys up or down.

3.Press the desired function key for this function.

The following message: "Programming Function Key Fx" will be displayed.

The message will disappear automatically and the function key is programmed.

4.Leave the adjustment mode by pressing ADJUST.

5.The function key is available in the operational mode.

e.g. programming horizontal phase on key F4.

1.Press ADJUST to enter the main menu (menu 1).

2.Push the cursor keys or to select 'Service menu'.

3.Press ENTER to go into the adjustment menus. A warning will be displayed (menu 2).

4.If qualified, press ENTER otherwise press EXIT and call for technical assistance.

5.Select Randon by pushing the cursor keys or .

6.Press ENTER to display the Random Access mode menu (menu 3).

7.Push the cursor keys or to select 'Geometry'.

8.Press ENTER to display the Geometry menu (menu 4).

9.Push the cursor keys or to select H PHASE (menu 4).

10.Press 'F4' to program this key.

11.Press ADJUST to return to operational mode.

MAIN MENU

Image Control

EYE-Q Control

Sound Control

Function keys

Service Menus

Select with or then <ENTER>

<EXIT> to return

menu 1

WARNING

RISK OF INCORRECT

ADJUSTMENT OF THE

PROJECTOR.

The following SERVICE menus are reserved to,

and to be performed only by qualified personnel !

If qualified, press <ENTER> to continue, or if not, <EXIT> to return.

menu 2

ADJUSTMENT MODE

Select a path from below :

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01 Select with or then <ENTER>

<EXIT> to return

menu 3

GEOMETRY

HPHASE RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

V SIZE

VLINEARITY H SIZE

BLANKING Select with or then <ENTER>

<EXIT> to return

menu 4

78

Image 80

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoInput Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Selection Menu Picture TuningRandom Access Adjustment Mode Picture TuningGain adjustment affects the brightest areas of the image Picture Tuning Color BalanceColor Balance Color BalanceColor Balance Sync Fast/Slow AdjustmentsPicture Tuning Clamp Tuning Piture TuningPeaking PeakingGeometry Adjustments Horizontal Phase AdjustmentsRandom Access Adjustment Mode GeometryRaster Shift Adjustments PhaseLeft-Right East-West Adjustments Forbidden AreaProjected Raster CRT Faceplate Border Phosphor Coarse ShiftLEFT-RIGHT Left Side Correction What can be done?Start up Left Side CorrectionTop-Bottom North-South Adjustments GeometryTOP-BOTTOM N-S TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeLinearity Vertical Linearity AdjustmentsLinearity V Size Vertical Size Adjustments Blanking AdjustmentsBlanking BlankingCorrect by pushing the cursor keys up or down Convergence Adjustments Converge AdjustmentConvergence ConvergenceFocusing FocusingFocusing MidpointLeft TOPBottom Color Select RightBlue on Source Color SelectService Mode Service ModeRandom Access Installation Service ModeProjector Setup Software version ConfigurationIdentification Text ON/OFFRun Time Projector SET-UPIdentification RUN TimeChange Password Change PasswordPassword Change PasswordChange Projector Address Change Baud RateProjector SET-UP Projector Address Baud RateProjector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Power Up Mode Common AddressCopy Mode Memory ManagementCopy a Block Memory ManagementDelete Mode Deletion of BlocksDeleting Block by Block Deletion of All BlocksSet to Midposition Covergence MidDelete ALL Blocks SET to MidpositionUndo R & B Convergence Mid Convergence MIDSET to Midposition Green Convergence MIDUndo Focus to Midposition Undo Green Convergence MidFocus to Midposition North-South Settings to Midposition East-West to MidpositionUndo East-West to Midposition To MidpositionUndo North-South Settings to Midposition Digital Vertical Linearity to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MIDDigital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MIDUndo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Dynamic Astigmatism GreenCommon Settings Gamma CorrectionsCRT Run In Cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position 12C Diagnostics Voltage DiagnosticsI2C Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks and Source Numbers Adjustment Blocks Memory BlocksSource Numbers Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsDimensions Bottom ViewSide View Front ViewSpecifications Page RUMA-009450 rev