Runco DTV-1200 owner manual Main Menu, Adjustment Mode

Page 30

Function Keys

What can be done?

Quick access keys to customer pre-programmed adjustments. Almost any adjustment can be added to a func- tion key. To program a function key, it is necessary to enter into the 'Service Menu'. To activate a function key, just press the corresponding key.

The following functions are factory pre-programmed : F1 = EYE-Q Touch up

F2 = Convergence Red on Green

F3 = Convergence Blue on Green

F4 = H & V Size

F5 = Color Balance

How to get an overview of the programmed keys?

1Push the cursor keys or to select 'Function Keys' (menu 1).

2Press ENTER to display an overview of the function keys (menu 2).

3Press EXIT to return.

MAIN MENU

Image Control

Eye-Q

Function Keys

Service Menus

Select with or then <ENTER> <EXIT> to return

menu 1

FUNCTION KEYS

F1: EYE-Q Touch Up

F2: Convergence Red on Green

F3: Convergence Blue on Green

F4: H & V Size

F5: Color Balance

<EXIT> to return

menu 2

Service Menus

What can be done?

With the complete set of Service menus such as EYE-Q, Guide, Random Access, Installation and Service it is possible to adjust the projector completely.

When entering the Service Menus, a warning will be displayed mentioning that only qualified Runco service personnel may enter the Service menus.

How to enter the Service Menu?

1Push the cursor keys or to select 'Service Menus' (menu 1).

2Press ENTER to select. A warning will be displayed (menu 2). "Risk of incorrect adjustment of the projector. The following SERVICE menus are reserved to and to be performed only by qualified personnel! If qualified, press <ENTER> to continue, or if not, <EXIT> to return.

MAIN MENU

Image Control

Eye-Q

Function Keys

Service Menus

Select with or then <ENTER> <EXIT> to return

menu 1

WARNING

RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR.

The following SERVICE menus are reserved to, and to be performed only by qualified personnel !

If qualified, press <ENTER> to continue, or if not, <EXIT> to return.

menu 2

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1 Select with or then <ENTER> <EXIT> to return

menu 3

28

Image 30

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoRGB Source to Input RGB Source with Composite Sync to Input 4/5Input Select Input RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5RS-232 Connection Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Brightness Control Contrast ControlColor Saturation Control Not used on the DTV-1200 Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Random Access Adjustment Mode Selection MenuPicture Tuning Picture TuningColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalanceSync Fast/Slow Adjustments Picture TuningColor Balance Peaking Clamp TuningPiture Tuning PeakingRandom Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustments GeometryRaster Shift Adjustments PhaseProjected Raster CRT Faceplate Border Phosphor Left-Right East-West AdjustmentsForbidden Area Coarse ShiftLEFT-RIGHT Start up Left Side CorrectionWhat can be done? Left Side CorrectionTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeVertical Linearity Adjustments Linearity V SizeLinearity Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceFocusing FocusingFocusing MidpointTOP BottomLeft Blue on Source Color SelectRight Color SelectRandom Access Installation Service ModeService Mode Service ModeIdentification Projector SetupSoftware version Configuration Text ON/OFFIdentification Run TimeProjector SET-UP RUN TimePassword Change PasswordChange Password Change PasswordProjector SET-UP Projector Address Change Projector AddressChange Baud Rate Baud RateProjector Warm Up Warm Up On/OffProjector Warm UP Warm Up Frequency Projector Warm Up TimeProjector Warm UP Power Up Mode Common AddressCopy a Block Copy ModeMemory Management Memory ManagementDeleting Block by Block Delete ModeDeletion of Blocks Deletion of All BlocksDelete ALL Blocks Set to MidpositionCovergence Mid SET to MidpositionSET to Midposition Undo R & B Convergence MidConvergence MID Green Convergence MIDUndo Green Convergence Mid Focus to MidpositionUndo Focus to Midposition Undo East-West to Midposition North-South Settings to MidpositionEast-West to Midposition To MidpositionUndo Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition DIG Vert Linearity MIDAstigmatism to Midposition Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition DIG HOR Linearity MIDAll Settings to Midposition Undo All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Dynamic Astigmatism GreenCRT Run In Cycle Common SettingsGamma Corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Menu PositionFlyback Turnover Point I2C Diagnostics 12C DiagnosticsVoltage Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsPhase Raster Shift Programmable Function KeysProgrammable Function Keys MESSAGES, Warnings and Failures Failure Source Numbers Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsSide View DimensionsBottom View Front ViewSpecifications Page RUMA-009450 rev