Runco DTV-1200 owner manual Input Selection via the Remote

Page 21

Input selection modes

Source No.	Projector Input	Remote Button No.

3	RGB	3

4/5	RGB (HV, S.O.G)	4 or 5

4/5	Component Video	6

4/5	RGB with Tri level sync	7

4/5	Component Video with
	Tri-level sync	8

Input Selection via the Remote.

With the digit buttons, it is possible to select one of the above input modes.

When the source is selected

When a valid and available source is selected, there will be information displayed on the screen about that source. This information includes:

-Source number

-Horizontal frequency

-Vertical frequency

Source 02

Fh= 63 kHz

Fv= 60 Hz

When the entry is a non valid source number, a warning appears on the screen: 'input not available'.

WARNING

Input not

available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source becomes available. A message 'source not available' will be displayed for a short time.

WARNING

Source not

available

When a Video or S-Video source is selected and no decoder is installed, the projector displays the folllowing message: 'Option not installed'.

WARNING

Option not

installed!

19

Image 21

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to ProjectorSource No Projector Input Remote Button No Source ConnectionsRGB Source to Input RGB Source with Composite Sync to Input 4/5Input Select Input RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5RS-232 Connection Getting Started Remote Control & Local KeypadAudio controls not used Projector Warm UP Stationary Image WarningFront of projector Remote Commands to the ProjectorProjector Address Input Selection via the Remote Brightness Control Contrast ControlColor Saturation Control Not used on the DTV-1200 Adjustment Mode Start UP of the Adjustment ModeMain Menu Main MenuImage Control Color AdjustFormat Select Compose Eye-Q Touch Up Eye-Q ControlEye-Q Auto Converge Main Menu Adjustment ModeService Menus Entering the Service MenusEnter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern VGA Internal Cross Hatch PatternPicture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture TuningPicture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color BalanceSync Fast/Slow Adjustments Picture TuningColor Balance Piture Tuning Clamp TuningPeaking PeakingHorizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode GeometryPhase Raster Shift AdjustmentsForbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse ShiftLEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side CorrectionGeometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-STOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOMSize Horizontal Size AdjustmentsVertical Linearity Adjustments Linearity V SizeLinearity Blanking Adjustments Vertical Size AdjustmentsBlanking BlankingCorrect by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence ConvergenceFocusing FocusingFocusing MidpointTOP BottomLeft Right Color SelectBlue on Source Color SelectService Mode Service ModeRandom Access Installation Service ModeSoftware version Configuration Projector SetupIdentification Text ON/OFFProjector SET-UP Run TimeIdentification RUN TimeChange Password Change PasswordPassword Change PasswordChange Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud RateProjector Warm Up Warm Up On/OffProjector Warm UP Warm Up Frequency Projector Warm Up TimeProjector Warm UP Common Address Power Up ModeMemory Management Copy ModeCopy a Block Memory ManagementDeletion of Blocks Delete ModeDeleting Block by Block Deletion of All BlocksCovergence Mid Set to MidpositionDelete ALL Blocks SET to MidpositionConvergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MIDUndo Green Convergence Mid Focus to MidpositionUndo Focus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To MidpositionDigital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MIDUndo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MIDAll Settings to Midposition Undo All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Green Dynamic AstigmatismGamma Corrections Common SettingsCRT Run In Cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Menu PositionFlyback Turnover Point Voltage Diagnostics 12C DiagnosticsI2C Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsPhase Raster Shift Programmable Function KeysProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR ConfigurationBottom View DimensionsSide View Front ViewSpecifications Page RUMA-009450 rev