Runco DTV-1200 Set to Midposition, Covergence Mid, Delete ALL Blocks, SET to Midposition

Page 65

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or then <ENTER>

<EXIT> to return

menu 1

DELETE ALL BLOCKS

!

All blocks

will be deleted!

<ENTER> to confirm

<EXIT> to cancel

menu 2

Set to Midposition

What can be done?

All adjustment settings (geometry and convergence) can be set to mid position. Item is password protected.

How to Start Up?

1.Push the cursor key or to highlight 'Set to Midposition' (menu 1).

2.Press ENTER to display the set to midposition menu (menu 2).

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or then <ENTER>

<EXIT> to return

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID DIG HOR LINEARITY MID ASTIGMATISM MIDPOSITION ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 2

R & B Covergence Mid

What can be done?

All convergence settings for red and blue are set to midposition. Item is password protected

How to set convergence to midposition:

1.Push the cursor key or to highlight 'R & B Convergence Mid' (menu 1).

2.Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3.Press ENTER to confirm.

63

Image 65

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to ProjectorSource No Projector Input Remote Button No Source ConnectionsInput Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Getting Started Remote Control & Local KeypadAudio controls not used Projector Warm UP Stationary Image WarningFront of projector Remote Commands to the ProjectorProjector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Adjustment Mode Start UP of the Adjustment ModeMain Menu Main MenuImage Control Color AdjustFormat Select Compose Eye-Q Touch Up Eye-Q ControlEye-Q Auto Converge Main Menu Adjustment ModeService Menus Entering the Service MenusEnter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern VGA Internal Cross Hatch PatternPicture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture TuningPicture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color BalanceColor Balance Sync Fast/Slow AdjustmentsPicture Tuning Piture Tuning Clamp TuningPeaking PeakingHorizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode GeometryPhase Raster Shift AdjustmentsForbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse ShiftLEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side CorrectionGeometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-STOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOMSize Horizontal Size AdjustmentsLinearity Vertical Linearity AdjustmentsLinearity V Size Blanking Adjustments Vertical Size AdjustmentsBlanking BlankingCorrect by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence ConvergenceFocusing FocusingFocusing MidpointLeft TOPBottom Right Color SelectBlue on Source Color SelectService Mode Service ModeRandom Access Installation Service ModeSoftware version Configuration Projector SetupIdentification Text ON/OFFProjector SET-UP Run TimeIdentification RUN TimeChange Password Change PasswordPassword Change PasswordChange Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud RateProjector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Common Address Power Up ModeMemory Management Copy ModeCopy a Block Memory ManagementDeletion of Blocks Delete ModeDeleting Block by Block Deletion of All BlocksCovergence Mid Set to MidpositionDelete ALL Blocks SET to MidpositionConvergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MIDUndo Focus to Midposition Undo Green Convergence MidFocus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To MidpositionDigital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MIDUndo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MIDUndo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Green Dynamic AstigmatismGamma Corrections Common SettingsCRT Run In Cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position Voltage Diagnostics 12C DiagnosticsI2C Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR ConfigurationBottom View DimensionsSide View Front ViewSpecifications Page RUMA-009450 rev