Runco DTV-1200 owner manual Failure

Page 82

FAILURE

I2C error

addr. : 7FH3

FAILURE

short

circuit on

I2C bus

FAILURE

invalid input

FAN FAILED

Projector will

switch off

FAILURE

EYE-Q

configuration failed

Hardware failure. Call a qualified serv- ice technician for repair.

Hardware failure. Call a qualified serv- ice technician for repair.

Input not valid

Projector switched off due to a fan fail.

Error occured while configuring the EYE-Q module.

80

Image 82

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoRGB Source with Composite Sync to Input 4/5 RGB Source to InputInput Select Input Component Source to Input 4/5 RGB Source with Tri-level Sync to Input 4/5RS-232 Connection Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Contrast Control Brightness ControlColor Saturation Control Not used on the DTV-1200 Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Random Access Adjustment Mode Selection MenuPicture Tuning Picture TuningColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalancePicture Tuning Sync Fast/Slow AdjustmentsColor Balance Peaking Clamp TuningPiture Tuning PeakingRandom Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustments GeometryRaster Shift Adjustments PhaseProjected Raster CRT Faceplate Border Phosphor Left-Right East-West AdjustmentsForbidden Area Coarse ShiftLEFT-RIGHT Start up Left Side CorrectionWhat can be done? Left Side CorrectionTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeLinearity V Size Vertical Linearity AdjustmentsLinearity Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceFocusing FocusingFocusing MidpointBottom TOPLeft Blue on Source Color SelectRight Color SelectRandom Access Installation Service ModeService Mode Service ModeIdentification Projector SetupSoftware version Configuration Text ON/OFFIdentification Run TimeProjector SET-UP RUN TimePassword Change PasswordChange Password Change PasswordProjector SET-UP Projector Address Change Projector AddressChange Baud Rate Baud RateWarm Up On/Off Projector Warm UpProjector Warm UP Projector Warm Up Time Warm Up FrequencyProjector Warm UP Power Up Mode Common AddressCopy a Block Copy ModeMemory Management Memory ManagementDeleting Block by Block Delete ModeDeletion of Blocks Deletion of All BlocksDelete ALL Blocks Set to MidpositionCovergence Mid SET to MidpositionSET to Midposition Undo R & B Convergence MidConvergence MID Green Convergence MIDFocus to Midposition Undo Green Convergence MidUndo Focus to Midposition Undo East-West to Midposition North-South Settings to MidpositionEast-West to Midposition To MidpositionUndo Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition DIG Vert Linearity MIDAstigmatism to Midposition Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition DIG HOR Linearity MIDUndo All Settings to Midposition All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Dynamic Astigmatism GreenCRT Run In Cycle Common SettingsGamma Corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Menu Position Flyback Turnover PointFlyback Turnover Point I2C Diagnostics 12C DiagnosticsVoltage Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Source Numbers Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsSide View DimensionsBottom View Front ViewSpecifications Page RUMA-009450 rev