Runco DTV-1200 owner manual Enter Password

Page 32

Password Protection

Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password. (Password protection is only available when the password strap on the contoller module is ON. Contact an authorized Runco technician when no password is requested during the adjustment proce- dure and password protection is desired.)

enter

password

x x x x

Entering the Password

Your password contains 4 digits.

Enter the digits with the numeric keys on the Remote.

Example : 1 1 1 1

For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'.

When the password is correct, you gain access to the selected item.

When the entered password is wrong, the error message 'wrong password !!!' will be displayed.

Note:

When the password is correctly entered, all other password protected items are accessible without re-entering the password.

When re-entering the adjustment mode, it will be necessary to enter your password again when selecting a password protected item.

30

Image 32
Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoInput Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Selection Menu Picture TuningRandom Access Adjustment Mode Picture TuningGain adjustment affects the brightest areas of the image Picture Tuning Color BalanceColor Balance Color BalanceColor Balance Sync Fast/Slow AdjustmentsPicture Tuning Clamp Tuning Piture TuningPeaking PeakingGeometry Adjustments Horizontal Phase AdjustmentsRandom Access Adjustment Mode GeometryRaster Shift Adjustments PhaseLeft-Right East-West Adjustments Forbidden AreaProjected Raster CRT Faceplate Border Phosphor Coarse ShiftLEFT-RIGHT Left Side Correction What can be done?Start up Left Side CorrectionTop-Bottom North-South Adjustments GeometryTOP-BOTTOM N-S TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeLinearity Vertical Linearity AdjustmentsLinearity V Size Vertical Size Adjustments Blanking AdjustmentsBlanking BlankingCorrect by pushing the cursor keys up or down Convergence Adjustments Converge AdjustmentConvergence ConvergenceFocusing FocusingFocusing MidpointLeft TOPBottom Color Select RightBlue on Source Color SelectService Mode Service ModeRandom Access Installation Service ModeProjector Setup Software version ConfigurationIdentification Text ON/OFFRun Time Projector SET-UPIdentification RUN TimeChange Password Change PasswordPassword Change PasswordChange Projector Address Change Baud RateProjector SET-UP Projector Address Baud RateProjector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Power Up Mode Common AddressCopy Mode Memory ManagementCopy a Block Memory ManagementDelete Mode Deletion of BlocksDeleting Block by Block Deletion of All BlocksSet to Midposition Covergence MidDelete ALL Blocks SET to MidpositionUndo R & B Convergence Mid Convergence MIDSET to Midposition Green Convergence MIDUndo Focus to Midposition Undo Green Convergence MidFocus to Midposition North-South Settings to Midposition East-West to MidpositionUndo East-West to Midposition To MidpositionUndo North-South Settings to Midposition Digital Vertical Linearity to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MIDDigital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MIDUndo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Dynamic Astigmatism GreenCommon Settings Gamma CorrectionsCRT Run In Cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position 12C Diagnostics Voltage DiagnosticsI2C Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks and Source Numbers Adjustment Blocks Memory BlocksSource Numbers Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsDimensions Bottom ViewSide View Front ViewSpecifications Page RUMA-009450 rev