Black Box IC026A-R2, IC026AE-R2 manual Getting Started, Inspection, Configuration, Serial Port

Page 14

RS-232↔IEEE 488 INTERFACE CONVERTER

3. Getting Started

3.1 Inspection

The interface converter was carefully inspected, both mechanically and electrically, prior to shipment. When you receive it, carefully unpack all items from the shipping carton and check for any obvious signs of damage that may have occurred during shipment. Immediately report any damage found to the shipping agent. Remember to retain all shipping materials in the event that shipment back to the factory becomes necessary.

Every interface converter is shipped with the following:

•RS-232↔IEEE 488 Interface Converter

•This instruction manual

•Power supply

3.2 Configuration

Three DIP switches internal to the interface converter set the configuration of the interface.

NOTE

Selectable functions are read only at power-on and should only be set prior to applying power to the interface. The following figures illustrate the factory-default conditions, which are:

Serial Port:	IEEE:
9600 Baud	Mode = IEEE 488 Controller
8 Data Bits	Address = 10
2 Stop Bits	Bus Terminator = LF; EOI Disabled
No Parity	Talk-Back on Terminator Enabled
Serial Terminator = LF	Talk-Back on Timeout Enabled
Echo Disabled
RTS/CTS Handshake

14

Image 14

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents Serial Interface SpecificationsIEEE-488 Interface Specifications GeneralIntroduction DescriptionAbbreviations Inspection ConfigurationGetting Started Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Switch SW2 Selecting the Serial Terminator Selecting Terminator SubstitutionSelecting the Mode Switch SW3 Selecting the Ieee Bus Terminator10. Switch SW2 Selecting the Mode Selecting the Ieee AddressFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels Clear To Send-Input-Pin RxD Receive Data-Input-PinTxD Transmit Data-Output-Pin Request To Send-Output-Pin+RxD Receive Data Plus-Input-Pin Vtest Test Voltage-Output-PinGnd Ground-Pin +TxD Transmit Data Plus-Output-PinRTS CTS General DSR RTS CTSGetting Started Controller Operation Controller-Mode Serial to Ieee OperationSerial and Ieee Terminator Substitution Talk-Back Features Ieee Address SelectionSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout 7470A SP1PA1000,1000PDPA1000,6000PUSP0Plotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Serial and Ieee Input Buffers Peripheral OperationPeripheral-Mode Operation Ieee Data Transfers Controlled BUS Data Transfers Serial-Poll Status-Byte Register DIO8 Ieee Input Buffer not EmptySerial Input Buffer not Empty RsvNot Defined-Always Ieee Input Buffer FullUse of Serial and Bus Terminators Ieee 488 Bus ImplementationUntalk UNT SW3 View for Ieee Address Selection General Structure Ieee 488 PrimerHistory RS-232↔IEEE 488 Interface Converter Send It to My Address DMMBus Management Lines Handshake Lines Data Valid DAVMultiline Commands Data LinesTalk Address Group TAG More on Service Requests Serial Poll Theory of Operation Address Device Part Number FunctionBoard Layout Component Layout of the Interface Converter’s MotherboardRED BLK Appendix A. Sample Dumb-Terminal Program CLSMultiline Messages SOHHow To Read the Chart Ascii CharacterIndex DIO1 DIO2 DIO3Index SW1 Copyright 1998. Black Box Corporation. All rights reserved