Black Box IC026AE-R2, IC026A-R2 manual SW3

Page 43

CHAPTER 4: Controller Operation

1 2 3 4 5 6 7 8

SW3

OPEN

IEEE Addr 5

IEEE Term CR

EOI Enabled

Switch

Side

View

DOT

	1	2	3	4	5	6	7	8
	SW2			OPEN
				OPEN
Mode	C
Talk-Back on Timeout	Enabled
Serial Term	CR
Echo	No Echo
Parity	No Parity

Switch

Side

View

DOT

1 2 3 4 5 6 7 8

SW1

OPEN

Baud Rate 57600

Handshake X-ON/X-OFF Word Length 7 Data Bits

Talk-Back on Terminator Enabled Stop Bits 1 Stop Bit

Switch

Side

View

DOT

Figure 4-10. Interface Converter Settings for Use with HP 7580A

Plotter on a Macintosh.

After configuration, turn on the plotter and the interface converter. The interface converter’s front-panel LEDs should all light momentarily while it performs an internal ROM and RAM test. All LEDs should go out except for the Power and Talk LED. The Talk LED indicates that the interface converter has detected the plotter on the IEEE bus and has addressed it to listen.

When the serial host begins to send the interface converter data, the Receive LED will flash. If it does not, this indicates that the interface is not receiving data from the serial host. Verify the cables are connected properly and the serial cable wiring. Verify the serial data format, word length, stop bits and parity.

43

Image 43

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents IEEE-488 Interface SpecificationsSerial Interface General SpecificationsDescription IntroductionAbbreviations Serial Port ConfigurationGetting Started InspectionSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Selecting Terminator Substitution Switch SW2 Selecting the Serial TerminatorSwitch SW3 Selecting the Ieee Bus Terminator Selecting the ModeSelecting the Ieee Address 10. Switch SW2 Selecting the ModeFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels Request To Send-Output-Pin RxD Receive Data-Input-PinTxD Transmit Data-Output-Pin Clear To Send-Input-Pin+TxD Transmit Data Plus-Output-Pin Vtest Test Voltage-Output-PinGnd Ground-Pin +RxD Receive Data Plus-Input-PinRTS CTS DSR RTS CTS GeneralGetting Started Controller-Mode Serial to Ieee Operation Controller OperationSerial and Ieee Terminator Substitution Ieee Address Selection Talk-Back FeaturesSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout SP1PA1000,1000PDPA1000,6000PUSP0 7470APlotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral-Mode Operation Peripheral OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers DIO8 Ieee Input Buffer not Empty Serial-Poll Status-Byte RegisterIeee Input Buffer Full RsvNot Defined-Always Serial Input Buffer not EmptyIeee 488 Bus Implementation Use of Serial and Bus TerminatorsUntalk UNT SW3 View for Ieee Address Selection History Ieee 488 PrimerGeneral Structure RS-232↔IEEE 488 Interface Converter DMM Send It to My AddressBus Management Lines Data Valid DAV Handshake LinesData Lines Multiline CommandsTalk Address Group TAG More on Service Requests Serial Poll Address Device Part Number Function Theory of OperationComponent Layout of the Interface Converter’s Motherboard Board LayoutRED BLK CLS Appendix A. Sample Dumb-Terminal ProgramSOH Multiline MessagesAscii Character How To Read the ChartDIO1 DIO2 DIO3 IndexIndex SW1 Copyright 1998. Black Box Corporation. All rights reserved