Black Box IC026A-R2, IC026AE-R2 manual Index, DIO1 DIO2 DIO3

Page 68

RS-232↔IEEE 488 INTERFACE CONVERTER

Index

Abbreviations
IEEE 488	13
Active Controller	53
Address Selection
IEEE	34
Applications
Plotter	38
Printer	44
ATN	56
Attention	56
Baud Rate	16
Blind Bus Data Transfers	46
Board Layout	63, 64
Bus Management Lines
Attention	56
End Or Identify	56
Interface Clear	56
Remote Enable	56
Service Request	57
CE Compliant
Operating Conditions	2
Character Codes	66
Clear To Send	27
Configuration	14
Connectors	26, 27
Controlled Bus Data Transfers .....47
Controller Features	24
Controller Mode Operation	32
Controller Operation	32
Data Lines	58
Data Transfers
Blind Bus	46
Controlled Bus	47
Data Valid	57
DAV	57
DCL	51, 59
Device Clear	51, 59
DIO1	49
DIO2	49
DIO3	49

DIO4		49
DIO5		49
DIO6		49
DIO7		49
DIO8		48
Echo		19
End Or Identify		56
EOI22, 56
Factory-Default Settings		14, 15
Feature Selections		24
Controller		24
Peripheral		25
Features
Talk Back		34-36
General Purpose
Interface Bus		53
GET		59
Go To Local		58
GPIB		53
Ground		28
Group Execute Trigger		59
GTL		58
Handshake Lines		57
Data Valid		57
Not Data Accepted		57
Not Ready For Data		57
IEEE 488 Abbreviations		13
IEEE 488 Bus
Implementation		50
IEEE 488 Primer		53
IEEE Address Selection		23, 34, 52
IEEE Bus Terminator		22
IEEE Controller
Mode	16, 22, 23, 32
IEEE Data Transfers		46
IEEE Multiline Messages		66
IEEE Peripheral		16
IFC		51, 56
Input Buffers		45
Inspecting the Unit		14

68

Image 68

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents Serial Interface SpecificationsIEEE-488 Interface Specifications GeneralIntroduction DescriptionAbbreviations Configuration Getting StartedInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Switch SW2 Selecting the Serial Terminator Selecting Terminator SubstitutionSelecting the Mode Switch SW3 Selecting the Ieee Bus Terminator10. Switch SW2 Selecting the Mode Selecting the Ieee AddressFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels RxD Receive Data-Input-Pin TxD Transmit Data-Output-PinClear To Send-Input-Pin Request To Send-Output-PinVtest Test Voltage-Output-Pin Gnd Ground-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS General DSR RTS CTSGetting Started Controller Operation Controller-Mode Serial to Ieee OperationSerial and Ieee Terminator Substitution Talk-Back Features Ieee Address SelectionSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout 7470A SP1PA1000,1000PDPA1000,6000PUSP0Plotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Serial and Ieee Input Buffers Peripheral OperationPeripheral-Mode Operation Ieee Data Transfers Controlled BUS Data Transfers Serial-Poll Status-Byte Register DIO8 Ieee Input Buffer not EmptyRsv Not Defined-AlwaysSerial Input Buffer not Empty Ieee Input Buffer FullUse of Serial and Bus Terminators Ieee 488 Bus ImplementationUntalk UNT SW3 View for Ieee Address Selection General Structure Ieee 488 PrimerHistory RS-232↔IEEE 488 Interface Converter Send It to My Address DMMBus Management Lines Handshake Lines Data Valid DAVMultiline Commands Data LinesTalk Address Group TAG More on Service Requests Serial Poll Theory of Operation Address Device Part Number FunctionBoard Layout Component Layout of the Interface Converter’s MotherboardRED BLK Appendix A. Sample Dumb-Terminal Program CLSMultiline Messages SOHHow To Read the Chart Ascii CharacterIndex DIO1 DIO2 DIO3Index SW1 Copyright 1998. Black Box Corporation. All rights reserved