Black Box IC026AE-R2, IC026A-R2 manual Contents

Page 9

CONTENTS

Chapter	Page
6.5 Handshake Lines	57
6.5.1 Data Valid (DAV)	57
6.5.2 Not Ready For Data (NRFD)	57
6.5.3 Not Data Accepted (NDAC)	57
6.6 Data Lines	58
6.7 Multiline Commands	58
6.7.1 Go To Local (GTL)	58
6.7.2 Listen Address Group (LAG)	58
6.7.3 Unlisten (UNL)	59
6.7.4 Talk Address Group (TAG)	59
6.7.5 Untalk (UNT)	59
6.7.6 Local Lockout (LLO)	59
6.7.7 Device Clear (DCL)	59
6.7.8 Selected Device Clear (SDC)	59
6.7.9 Serial Poll Disable (SPD)	59
6.7.10 Serial Poll Enable (SPE)	59
6.7.11 Group Execute Trigger (GET)	59
6.7.12 Take Control (TCT)	60
6.7.13 Secondary Command Group (SCG)	60
6.7.14 Parallel Poll Configure (PPC)	60
6.7.15 Parallel Poll Unconfigure (PPU)	60
6.8 More on Service Requests	60
6.8.1 Serial Poll	61
6.8.2 Parallel Poll	61
7. Theory of Operation and Board Layout	62
7.1 Theory of Operation	62
7.2 Board Layout	63
Appendix A: Sample Dumb-Terminal Program	65
Appendix B: Character Codes and IEEE Multiline Messages	66
Index	68

9

Image 9

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents Specifications IEEE-488 InterfaceSerial Interface General SpecificationsDescription IntroductionAbbreviations Getting Started ConfigurationInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Selecting Terminator Substitution Switch SW2 Selecting the Serial TerminatorSwitch SW3 Selecting the Ieee Bus Terminator Selecting the ModeSelecting the Ieee Address 10. Switch SW2 Selecting the ModeFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels TxD Transmit Data-Output-Pin RxD Receive Data-Input-PinClear To Send-Input-Pin Request To Send-Output-PinGnd Ground-Pin Vtest Test Voltage-Output-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS DSR RTS CTS GeneralGetting Started Controller-Mode Serial to Ieee Operation Controller OperationSerial and Ieee Terminator Substitution Ieee Address Selection Talk-Back FeaturesSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout SP1PA1000,1000PDPA1000,6000PUSP0 7470APlotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral Operation Peripheral-Mode OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers DIO8 Ieee Input Buffer not Empty Serial-Poll Status-Byte RegisterNot Defined-Always RsvSerial Input Buffer not Empty Ieee Input Buffer FullIeee 488 Bus Implementation Use of Serial and Bus TerminatorsUntalk UNT SW3 View for Ieee Address Selection Ieee 488 Primer HistoryGeneral Structure RS-232↔IEEE 488 Interface Converter DMM Send It to My AddressBus Management Lines Data Valid DAV Handshake LinesData Lines Multiline CommandsTalk Address Group TAG More on Service Requests Serial Poll Address Device Part Number Function Theory of OperationComponent Layout of the Interface Converter’s Motherboard Board LayoutRED BLK CLS Appendix A. Sample Dumb-Terminal ProgramSOH Multiline MessagesAscii Character How To Read the ChartDIO1 DIO2 DIO3 IndexIndex SW1 Copyright 1998. Black Box Corporation. All rights reserved