Black Box IC026A-R2, IC026AE-R2 manual Vtest Test Voltage-Output-Pin, Gnd Ground-Pin

Page 28

RS-232↔IEEE 488 INTERFACE CONVERTER

Vtest

Test Voltage—Output—Pin 6

This pin is connected to +5 volts through a 1K resistor. It is also common to Vtest on Pin 9.

Gnd	Ground—Pin 7

This pin sets the ground reference point for the other RS-232 inputs and outputs.

Vtest

Test Voltage—Output—Pin 9

This pin is connected to +5 volts through a 1K resistor. It is also common to Vtest on Pin 6.

+RxD	Receive Data Plus—Input—Pin 14

This pin accepts serial data sent by the RS-422 host. The serial data is expected with the word length, baud rate, stop bits, and parity selected by the internal switches. The signal level is high true and only connected to this pin when RS-422 operation is selected. It is 180 degrees out of phase with -RxD.

+TxD	Transmit Data Plus—Output—Pin 16

This pin transmits serial data to the RS-422 host. The serial data is sent with the word length, baud rate, stop bits, and parity selected by the internal switches. The signal level is high true and only connected to this pin when RS-422 operation is selected. It is 180 degrees out of phase with -TxD.

28

Image 28

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents IEEE-488 Interface SpecificationsSerial Interface Specifications GeneralIntroduction DescriptionAbbreviations Configuration Getting StartedInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Switch SW2 Selecting the Serial Terminator Selecting Terminator SubstitutionSelecting the Mode Switch SW3 Selecting the Ieee Bus Terminator10. Switch SW2 Selecting the Mode Selecting the Ieee AddressFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels RxD Receive Data-Input-Pin TxD Transmit Data-Output-PinClear To Send-Input-Pin Request To Send-Output-PinVtest Test Voltage-Output-Pin Gnd Ground-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS General DSR RTS CTSGetting Started Controller Operation Controller-Mode Serial to Ieee OperationSerial and Ieee Terminator Substitution Talk-Back Features Ieee Address SelectionSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout 7470A SP1PA1000,1000PDPA1000,6000PUSP0Plotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral-Mode Operation Peripheral OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers Serial-Poll Status-Byte Register DIO8 Ieee Input Buffer not EmptyRsv Not Defined-AlwaysSerial Input Buffer not Empty Ieee Input Buffer FullUse of Serial and Bus Terminators Ieee 488 Bus ImplementationUntalk UNT SW3 View for Ieee Address Selection History Ieee 488 PrimerGeneral Structure RS-232↔IEEE 488 Interface Converter Send It to My Address DMMBus Management Lines Handshake Lines Data Valid DAVMultiline Commands Data LinesTalk Address Group TAG More on Service Requests Serial Poll Theory of Operation Address Device Part Number FunctionBoard Layout Component Layout of the Interface Converter’s MotherboardRED BLK Appendix A. Sample Dumb-Terminal Program CLSMultiline Messages SOHHow To Read the Chart Ascii CharacterIndex DIO1 DIO2 DIO3Index SW1 Copyright 1998. Black Box Corporation. All rights reserved