Black Box IC026A-R2, IC026AE-R2 manual Specifications, IEEE-488 Interface, Serial Interface

Page 10

RS-232↔IEEE 488 INTERFACE CONVERTER

1. Specifications

IEEE-488 Interface

Implementation —

Terminators —

Connector —

Serial Interface

EIA RS-232C —

EIA RS-422A —

Character Set —

Output Voltage —

Input Voltage —

Baud Rate —

Data Format —

Duplex —

Serial Control —

Terminators —

Connector —

C1, C2, C3, C4, and C28 controller subsets. Serial to IEEE: SH1, AH1, T6, TE0, L4, LE0, SR1, RL0, PP0, DC1, DT0, E1.

Selectable CR, LF, LF-CR, and CR-LF with EOI

Standard IEEE 488 connector with metric studs

AB, BA, BB, CA, CB

Balanced voltage on TxD and RxD

Asynchronous bit serial

±5 volts min. (RS-232C); 5 volts typical (RS-422A)

±3 volts min.; q15v max.

Selectable 110, 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600, 19,200, and 57,600

Selectable 7 or 8 data bits; 1 or 2 stop bits; odd, even, mark, space, and no parity on transmit

Full with Echo/No Echo

Selectable CTS/RTS or XON/XOFF

Selectable CR, LF, LF-CR, and CR-LF

25-pin sub-D male, DCE configured

10

Image 10

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents IEEE-488 Interface SpecificationsSerial Interface Specifications GeneralIntroduction DescriptionAbbreviations Inspection ConfigurationGetting Started Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Switch SW2 Selecting the Serial Terminator Selecting Terminator SubstitutionSelecting the Mode Switch SW3 Selecting the Ieee Bus Terminator10. Switch SW2 Selecting the Mode Selecting the Ieee AddressFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels Clear To Send-Input-Pin RxD Receive Data-Input-PinTxD Transmit Data-Output-Pin Request To Send-Output-Pin+RxD Receive Data Plus-Input-Pin Vtest Test Voltage-Output-PinGnd Ground-Pin +TxD Transmit Data Plus-Output-PinRTS CTS General DSR RTS CTSGetting Started Controller Operation Controller-Mode Serial to Ieee OperationSerial and Ieee Terminator Substitution Talk-Back Features Ieee Address SelectionSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout 7470A SP1PA1000,1000PDPA1000,6000PUSP0Plotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral-Mode Operation Peripheral OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers Serial-Poll Status-Byte Register DIO8 Ieee Input Buffer not EmptySerial Input Buffer not Empty RsvNot Defined-Always Ieee Input Buffer FullUse of Serial and Bus Terminators Ieee 488 Bus ImplementationUntalk UNT SW3 View for Ieee Address Selection History Ieee 488 PrimerGeneral Structure RS-232↔IEEE 488 Interface Converter Send It to My Address DMMBus Management Lines Handshake Lines Data Valid DAVMultiline Commands Data LinesTalk Address Group TAG More on Service Requests Serial Poll Theory of Operation Address Device Part Number FunctionBoard Layout Component Layout of the Interface Converter’s MotherboardRED BLK Appendix A. Sample Dumb-Terminal Program CLSMultiline Messages SOHHow To Read the Chart Ascii CharacterIndex DIO1 DIO2 DIO3Index SW1 Copyright 1998. Black Box Corporation. All rights reserved