Dell BMX01 Technical Specifications

Technical Specifications

Enclosure Specifications

Power Supply Module

AC/DC power supply (per power supply)

Wattage 2700 W

Connector IEC C20

Heat dissipation 1205 BTU/hr (maximum)

Maximum inrush current Under typical line conditions and over the entire system

ambient operating range, the inrush current may reach 55 A

per power supply for 10 ms or less.

System voltage requirements 16 A, 100 V AC to 240 V AC, 50 Hz/60 Hz

Optional Avocent iKVM Module

Externally accessible connectors

USB Two 4-pin, USB 2.0-compliant connectors for keyboard and

mouse support

ACI port RJ-45

Video 15-pin VGA

Chassis Management Controller Module

Externally accessible connectors

Remote management Two dedicated 10/100/1000 Mb RJ-45 (for integrated

Ethernet remote access controller). Gb port connects to the

external management network. STK port allows CMCs in

adjacent enclosures to be daisy chained.

Serial 9-pin, DTE, 16550-compatible

Video 15-pin VGA

Battery CR 2032 3.0-V Lithium ion coin cell

Contents

Main Notes, Cautions, and Warnings Contents Page Page Page About Your System System Overview Page Page LCD Module LCD Module Features Using The LCD Module Menus Main Menu LCD Setup Menu Server Menu Configuration Wizard Back-Panel Features Page Fan Module Indicators Avocent iKVM Analog Switch Module (Optional) Avocent Analog iKVM Switch Module Features And Indicators CMC Module CMC Module Features Dell Chassis Management Controller Administrator Reference Guide CMC Fail-Safe Mode Daisy-Chain CMC Network Connection System Messages Other Information You May Need Getting Started Guide Page Initial System Configuration Before You Begin Getting Started Guide Initial Setup Sequence Initial CMC Network Configuration Configuring The CMC Using The LCD Configuration Wizard Configuring The CMC Using A Management Station And CLI Logging In To The CMC Using The Web-Based Interface <port number> <CMC IP address> Adding And Managing CMC Users Configuring iDRAC Networking Using The Web-Based Interface Setting The First Boot Device For Servers Configuring And Managing Power Installing Or Updating The CMC Firmware Downloading The CMC Firmware Updating The CMC Firmware Using The Web-Based Interface Updating The CMC Firmware Using RACADM Configuring The Optional iKVM Switch Module Updating The iKVM Firmware If the switch requires a USB SIP If the switch does not require a SIP to connect to the iKVM Tiering The Avocent iKVM Switch From A Digital KVM Switch Configuring The Analog Switch If the switch does not require a SIP to connect to the iKVM If the analog switch requires a USB SIP Resynchronizing The Server List At The Remote Client Workstation Viewing And Selecting Servers or FlexAddress FlexAddress Plus Configuring The I/O Modules Network Information I/O Connectivity General I/O Module Configuration Guidelines Fabric A Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only) Mezzanine Cards PowerEdge M610x Only Full-Height Blades Half-Height Blades Page Quarter-Height Blades I/O Module Port MappingFull-Height Blades n n+8 Standard LOM (Dual-Port) Mapping Page Page Page Page Page (n+24) I/O Module Port MappingHalf-Height Blades +16 n+16 Standard LOM (Dual-Port) and Network Daughter Card (Quad-Port) Mapping Page Page I/O Module Port MappingQuarter-Height Blades Standard LOM (Dual-Port) Mapping Page Page Page Page I/O ModulesSwitches Configuring A Switch Module Network Ethernet Port Using The Web-Based Interface Mellanox M4001F/M4001Q Infiniband Switch I/O Module Dell PowerConnect KR 8024-k Switch Dell PowerConnect M8428-k 10 Gb Converged Network Switch Mellanox M2401G DDR Infiniband Switch I/O Module Mellanox M3601Q QDR Infiniband Switch I/O Module Cisco Catalyst Ethernet Switch I/O Modules Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module Dell PowerConnect M6220 Ethernet Switch I/O Module Dell PowerConnect M8024 10 Gb Ethernet Switch I/O Module Dell 8/4 Gbps FC SAN Module I/O ModulesPass-Through Dell 4 Gbps Fibre Channel Pass-Through Module Page Dell 10 GbE KR Pass-Through I/O Module Dell 10 Gb Ethernet Pass-Through Module II 10/100/1000 Mb Ethernet Pass-Through I/O Module Brocade M4424 SAN I/O Module Page Brocade M5424 FC8 I/O Module Page Page Page Installing Enclosure Components Recommended Tools Removing And Installing A Blade Removing A Blade Page Installing A Blade Removing And Installing A Sleeve Removing The Sleeve Installing The Sleeve Power Supply Modules Power Supply Blanks Removing A Power Supply Module Page Installing a Power Supply Module Fan Modules Removing A Fan Module Installing a Fan Module CMC Module Removing A CMC Module Installing A CMC Module CMC Module SD Card iKVM Module Removing An iKVM Module Installing An iKVM Module I/O Modules Removing An I/O Module Installing An I/O Module Enclosure Bezel Removing The Enclosure Bezel Installing The Enclosure Bezel Enclosure Midplane Removing The Front Module Cage Assembly And Midplane Page Installing The Midplane And Front Module Cage Assembly Enclosure Control Panel Assembly Removing The Control Panel Installing The Control Panel LCD Module Removing The LCD Module Installing The LCD Module Page Troubleshooting The Enclosure Safety FirstFor You and Your System Responding to a Systems Management Alert Message Troubleshooting A Damaged Enclosure Troubleshooting Enclosure Components Troubleshooting A Wet Enclosure Troubleshooting Power Supply Modules Troubleshooting Fan Modules Troubleshooting The iKVM Module Troubleshooting I/O Modules Page Technical Specifications Enclosure Specifications I/O Module Specifications Page Owner's Manual Getting Help Contacting Dell