Power Supply Modules, Installing The Sleeve | Dell BMX01 guide

Figure 36. Removing and Installing a Sleeve
1. sleeve handle cover		5. guide rail on enclosure
2. sleeve handle		6. sleeve
3.	sleeve/blade slot
4.	guide rail on sleeve

Installing The Sleeve

1.Remove the I/O connector covers from the I/O connectors on the sleeve and save for future use.

2.Remove the cover from the sleeve handle.

NOTE: To ensure optimal thermal performance, do not replace the cover on the sleeve handle after the sleeve is installed in the enclosure.

3.If installed, remove the blade or blade blank from the top slot (Blade a) of the sleeve.

CAUTION: If you are installing a sleeve in bays 3 or 4, rotate the LCD module to the horizontal storage position to prevent accidental damage to the LCD screen.

4.Align the guide rail on the upper edge of the sleeve so that the rail fits between the plastic guides on the enclosure.

5.Slide the sleeve into the enclosure.

6.Lift the sleeve handle up to secure the sleeve in the enclosure.

Power Supply Modules

The Dell PowerEdge M1000e enclosure supports up to six hot-swappable power supply modules, accessible from the enclosure back panel.

74

Image 74

Dell BMX01 owner manual Power Supply Modules, Installing The Sleeve

Contents

Regulatory Model BMX01 Page Contents Configuring The I/O Modules Installing Enclosure Components Getting Help Troubleshooting The EnclosureTechnical Specifications About Your System System Overview Blade Numbering Full Height Blades System Control-Panel Features Blade Numbering Quarter Height Blades LCD Module LCD Module Features LCD Display Center button Configuration WizardUsing The LCD Module Menus Back-Panel Features Back-Panel Features Power Supply Indicators Back-Panel Module Bay Numbering Power to the system Fan Module IndicatorsIndicator Description Power supply fault Icon Indicator Avocent iKVM Analog Switch Module Optional Solid Green Avocent Analog iKVM Switch Module Features And Indicators CMC Module Features CMC Module CMC network cable CMC Fail-Safe ModeCondition Description CMC removal Daisy-Chain CMC Network Connection System Messages Other Information You May NeedPage Before You Begin Initial Setup SequenceInitial CMC Network Configuration Configuring The CMC Using The LCD Configuration Wizard Configuring The CMC Using a Management Station And CLI Https//CMC IP addressport number Logging In To The CMC Using The Web-Based InterfaceHttps//CMC IP address Adding And Managing CMC Users Configuring iDRAC Networking Using The Web-Based InterfaceClick Setup → Deploy Installing Or Updating The CMC Firmware Setting The First Boot Device For ServersConfiguring And Managing Power Downloading The CMC Firmware Updating The CMC Firmware Using The Web-Based InterfaceUpdating The CMC Firmware Using Racadm Tiering The Avocent iKVM Switch From An Analog KVM Switch Configuring The Optional iKVM Switch ModuleTiering The Avocent iKVM Switch From a Digital KVM Switch Updating The iKVM Firmware Configuring The Analog Switch Click Setup → Devices → Device Modify Viewing And Selecting Servers FlexAddress FlexAddress Plus Connectivity General I/O Module Configuration GuidelinesNetwork Information Fabric a Fabric B Fabric C Full-Height Blades PowerEdge M610x OnlyMezzanine Cards Half-Height Blades Supported I/O Module Configurations Standard LOM Dual-Port Mapping Module Port Mapping-Full-Height BladesQuarter-Height Blades Dual-Port Mezzanine Cards Blade Module Mezzanine Card C Port Mezzanine Card B Blade Module Blade Module Mezz1FabC Port Mezz2FabB Mezz3FabC Port Mezz4FabB Blade Module Quad-Port Mezzanine Cards +8Port4 Module Port MappingHalf-Height BladesMezzFABCBlade n Example of I/O Module Port Assignments Half-Height Blade Blade n Integrated LOM1 Port n Integrated LOM2 Module Port Mapping-Quarter-Height Blades Blade n Module Dual-Port Mezzanine Cards Sleeve Module Sleeve Module Quad-Port Mezzanine Cards Modules-Switches Mellanox M4001F/M4001Q Infiniband Switch I/O Module Dell PowerConnect KR 8024-k Switch Mellanox M4001F/M4001Q Infiniband Switch Module Dell PowerConnect M8428-k 10 Gb Converged Network Switch Dell PowerConnect KR 8024-k Switch Mellanox M2401G DDR Infiniband Switch I/O Module Dell PowerConnect M8428-k 10 Gb Converged Network Switch Mellanox M3601Q QDR Infiniband Switch I/O Module Mellanox M2401G DDR Infiniband Switch Module Cisco Catalyst Ethernet Switch I/O Modules Mellanox M3601Q QDR Infiniband Switch I/O Module Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module Cisco Catalyst Ethernet Switch Module Features Dell PowerConnect M6220 Ethernet Switch I/O Module PowerConnect M6348 1 Gb Ethernet Switch I/O Module Features Dell PowerConnect M8024 10 Gb Ethernet Switch I/O Module PowerConnect M6220 Ethernet Switch I/O Module PowerConnect M8024 10 Gb Ethernet Switch I/O Module Dell 8/4 Gbps FC SAN Module Modules-Pass-Through Dell 4 Gbps Fibre Channel Pass-Through Module Status/Identification Indicator Installed Dell 10 GbE KR Pass-Through I/O Module Dell 10 GbE KR Pass-Through I/O Module Dell 10 Gb Ethernet Pass-Through Module 10/100/1000 Mb Ethernet Pass-Through I/O Module Brocade M4424 SAN I/O Module 100/1000 Mb Ethernet Pass-Through I/O Module Brocade M4424 SAN I/O Module Brocade M5424 FC8 I/O Module Brocade M5424 FC8 I/O Module Module power indicator Page Removing a Blade Removing And Installing a BladeRecommended Tools Blade handle Removing The Sleeve Removing And Installing a SleeveInstalling a Blade Power Supply Modules Installing The Sleeve Power Supply Blanks Removing a Power Supply Module Power Cable Retention Clip Installing a Power Supply Module Fan Modules Installing a Fan Module Removing a Fan Module Installing a CMC Module Removing a CMC Module Click the Power Management tab Select the Reset CMC warm boot button Removing An iKVM Module Installing An iKVM ModuleIKVM Module Modules Removing An I/O Module Removing The Enclosure Bezel Installing An I/O ModuleEnclosure Bezel Enclosure Midplane Installing The Enclosure BezelRemoving The Front Module Cage Assembly And Midplane Front module cage assembly Enclosure Torx T20 screws Installing The Midplane And Front Module Cage Assembly Removing and Installing the Midplane Enclosure Control Panel Assembly Removing The Control Panel Installing The Control Panel Removing The LCD Module Installing The LCD Module Removing and Installing the LCD ModulePage Troubleshooting The Enclosure Troubleshooting Enclosure Components Troubleshooting a Wet Enclosure Troubleshooting Power Supply Modules Troubleshooting I/O Modules Troubleshooting Fan ModulesTroubleshooting The iKVM Module Page Optional Avocent iKVM Module Enclosure SpecificationsPower Supply Module Chassis Management Controller Module Brocade FC8 Fibre Channel Switch Module Module SpecificationsPowerConnect M6220 Ethernet Switch Module Brocade FC4 Fibre Channel Switch Module Gb Ethernet Pass-Through Module Mellanox M4001F/M4001Q Infiniband Switch I/O ModuleMellanox Infiniband Switch Module Fibre Channel Pass-Through Module Dell PowerConnect M8024 10 Gb Ethernet switch I/O module Contacting Dell Visit support.dell.com