Black Box IC026A-R2, IC026AE-R2 manual RS-232↔IEEE 488 Interface Converter

Page 4

RS-232↔IEEE 488 INTERFACE CONVERTER

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.

4

Image 4

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents IEEE-488 Interface SpecificationsSerial Interface Specifications GeneralIntroduction DescriptionAbbreviations Configuration Getting StartedInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Switch SW2 Selecting the Serial Terminator Selecting Terminator SubstitutionSelecting the Mode Switch SW3 Selecting the Ieee Bus Terminator10. Switch SW2 Selecting the Mode Selecting the Ieee AddressFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels RxD Receive Data-Input-Pin TxD Transmit Data-Output-PinClear To Send-Input-Pin Request To Send-Output-PinVtest Test Voltage-Output-Pin Gnd Ground-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS General DSR RTS CTSGetting Started Controller Operation Controller-Mode Serial to Ieee OperationSerial and Ieee Terminator Substitution Talk-Back Features Ieee Address SelectionSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout 7470A SP1PA1000,1000PDPA1000,6000PUSP0Plotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral-Mode Operation Peripheral OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers Serial-Poll Status-Byte Register DIO8 Ieee Input Buffer not EmptyRsv Not Defined-AlwaysSerial Input Buffer not Empty Ieee Input Buffer FullUse of Serial and Bus Terminators Ieee 488 Bus ImplementationUntalk UNT SW3 View for Ieee Address Selection History Ieee 488 PrimerGeneral Structure RS-232↔IEEE 488 Interface Converter Send It to My Address DMMBus Management Lines Handshake Lines Data Valid DAVMultiline Commands Data LinesTalk Address Group TAG More on Service Requests Serial Poll Theory of Operation Address Device Part Number FunctionBoard Layout Component Layout of the Interface Converter’s MotherboardRED BLK Appendix A. Sample Dumb-Terminal Program CLSMultiline Messages SOHHow To Read the Chart Ascii CharacterIndex DIO1 DIO2 DIO3Index SW1 Copyright 1998. Black Box Corporation. All rights reserved