Black Box IC026AE-R2, IC026A-R2 manual Rts Cts

Page 29

CHAPTER 3: Getting Started

3.8.3SERIAL-CABLE WIRING DIAGRAMS

If a cable was not purchased with the interface, the following diagrams will be helpful in making your own cable. Simple soldering skills and an attention to detail will ensure successful construction.

Mini DINs Male		DB25 Male
RTS 1		4	CTS

CTS 2		5	RTS
-TxD 3		2	-RxD
Gnd 4		7	Gnd
-RxD 5		3	-TxD
+TxD 6		14 +RxD
+RxD 8		16 +TxD

Figure 3-17. Wiring Diagram:

Macintosh to Interface Converter (RS-422).

DB25 Female		DB25 Male
-TxD 2		2	-RxD

-RxD 3		3	-TxD

RTS 4		4	CTS

CTS 5		5	RTS

DSR 6		3	V test

Gnd 7		7	Gnd

Figure 3-18. Wiring Diagram: IBM PC or Compatible with DB25 Serial Connector to Interface Converter (RS-232).

29

Image 29

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents Serial Interface SpecificationsIEEE-488 Interface General SpecificationsDescription IntroductionAbbreviations Getting Started ConfigurationInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Selecting Terminator Substitution Switch SW2 Selecting the Serial TerminatorSwitch SW3 Selecting the Ieee Bus Terminator Selecting the ModeSelecting the Ieee Address 10. Switch SW2 Selecting the ModeFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels TxD Transmit Data-Output-Pin RxD Receive Data-Input-PinClear To Send-Input-Pin Request To Send-Output-PinGnd Ground-Pin Vtest Test Voltage-Output-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS DSR RTS CTS GeneralGetting Started Controller-Mode Serial to Ieee Operation Controller OperationSerial and Ieee Terminator Substitution Ieee Address Selection Talk-Back FeaturesSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout SP1PA1000,1000PDPA1000,6000PUSP0 7470APlotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Serial and Ieee Input Buffers Peripheral OperationPeripheral-Mode Operation Ieee Data Transfers Controlled BUS Data Transfers DIO8 Ieee Input Buffer not Empty Serial-Poll Status-Byte RegisterNot Defined-Always RsvSerial Input Buffer not Empty Ieee Input Buffer FullIeee 488 Bus Implementation Use of Serial and Bus TerminatorsUntalk UNT SW3 View for Ieee Address Selection General Structure Ieee 488 PrimerHistory RS-232↔IEEE 488 Interface Converter DMM Send It to My AddressBus Management Lines Data Valid DAV Handshake LinesData Lines Multiline CommandsTalk Address Group TAG More on Service Requests Serial Poll Address Device Part Number Function Theory of OperationComponent Layout of the Interface Converter’s Motherboard Board LayoutRED BLK CLS Appendix A. Sample Dumb-Terminal ProgramSOH Multiline MessagesAscii Character How To Read the ChartDIO1 DIO2 DIO3 IndexIndex SW1 Copyright 1998. Black Box Corporation. All rights reserved