Black Box IC026AE-R2, IC026A-R2 manual Serial Interface

Page 25

CHAPTER 3: Getting Started

3.7.2PERIPHERAL FEATURES

In the IEEE Peripheral (IEEE 488 to RS-232 converter) mode, SW1-7 enables the interface to assert the SRQ IEEE bus interface line to indicate that it has received the last switch selected serial terminator character from the serial device.

1 2 3 4 5 6 7 8

OPEN

SRQ on Last

Terminator Disabled

1 2 3 4 5 6 7 8

OPEN

SRQ on Last

Terminator Enabled

Switch

Side

View

DOT

Figure 3-14. Switch SW1: Enabling or Disabling SRQ on Last Serial

Terminator in Peripheral Mode.

3.8 Serial Interface

The interface converter has the ability to output signal levels that are compatible with either RS-232 or RS-422. An internal DIP shorting plug determines which electrical specification is chosen. If the interface is to be connected to an IBM® PC or compatible, the RS-232 level should be selected. If it will be connected to a Macintosh®, the RS-422 level should be used. For connection to other computers, refer to the manufacturer’s manual to determine which levels are supported.

25

Image 25

Contents RS-232↔IEEE Interface Converter RS-232↔IEEE 488 Interface Converter Trademarks Used in this Manual RS-232↔IEEE 488 Interface Converter NOM Statement RS-232↔IEEE 488 Interface Converter Contents RS-232↔IEEE 488 Interface Converter Contents IEEE-488 Interface SpecificationsSerial Interface General SpecificationsDescription IntroductionAbbreviations Getting Started ConfigurationInspection Serial PortSW3 Serial Port Settings Switch SW1 Selecting the Serial Baud Rate Switch SW1 Selecting the Serial Word Length Data Bits Switch SW2 Selecting the Serial Parity Switch SW1 Selecting the Serial Handshake Selecting Terminator Substitution Switch SW2 Selecting the Serial TerminatorSwitch SW3 Selecting the Ieee Bus Terminator Selecting the ModeSelecting the Ieee Address 10. Switch SW2 Selecting the ModeFeature Selections Serial Interface 15. Selecting RS-232 or RS-422 Signal Levels TxD Transmit Data-Output-Pin RxD Receive Data-Input-PinClear To Send-Input-Pin Request To Send-Output-PinGnd Ground-Pin Vtest Test Voltage-Output-Pin+RxD Receive Data Plus-Input-Pin +TxD Transmit Data Plus-Output-PinRTS CTS DSR RTS CTS GeneralGetting Started Controller-Mode Serial to Ieee Operation Controller OperationSerial and Ieee Terminator Substitution Ieee Address Selection Talk-Back FeaturesSwitch SW1 Enabling or Disabling Talk-Back on Terminator Switch SW2 Enabling or Disabling Talk-Back on Timeout SP1PA1000,1000PDPA1000,6000PUSP0 7470APlotter Applications A PC-Based Graphics System SW3 MacPlot Configuration Screen Setting the Internal DIP Shorting Jumper for RS-422 SW3 Printer Applications Peripheral-Mode Operation Peripheral OperationSerial and Ieee Input Buffers Ieee Data Transfers Controlled BUS Data Transfers DIO8 Ieee Input Buffer not Empty Serial-Poll Status-Byte RegisterNot Defined-Always RsvSerial Input Buffer not Empty Ieee Input Buffer FullIeee 488 Bus Implementation Use of Serial and Bus TerminatorsUntalk UNT SW3 View for Ieee Address Selection History Ieee 488 PrimerGeneral Structure RS-232↔IEEE 488 Interface Converter DMM Send It to My AddressBus Management Lines Data Valid DAV Handshake LinesData Lines Multiline CommandsTalk Address Group TAG More on Service Requests Serial Poll Address Device Part Number Function Theory of OperationComponent Layout of the Interface Converter’s Motherboard Board LayoutRED BLK CLS Appendix A. Sample Dumb-Terminal ProgramSOH Multiline MessagesAscii Character How To Read the ChartDIO1 DIO2 DIO3 IndexIndex SW1 Copyright 1998. Black Box Corporation. All rights reserved