Runco V-63HD, V-50HD operation manual Input Position, Resolution

Page 48

Operation

Input Position ➤

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Overscan Mode

Phase

Tracking

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5.Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Picture menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source.

Note	The input position settings are automatically saved for each input
	and resolution.

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Press to shift the image to the right; press to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Press to shift the image upward; press to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Press to increase the width; press to decrease it.

36	Vistage™ Series Flat-Panel Display Installation/Operation Manual

Image 48

Contents Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor DHD Controller Front Panel Primary InputMessages from the Hdmi Audio Out connector DHD Controller Rear PanelV-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote ControlLight For more information about aspect ratios, refer to TableCinema Controls and Functions Installation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer OperationInstallation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandAmbient Light Other ConsiderationsRack-Mounting the DHD ControllerConnecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller OptionalRS-232 Controller ConnectionEthernet Network Turning on the Power Connecting to AC PowerSetting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionService Main Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativeScreen PictureScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep TimerSignal InformationInformation SystemYou must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copied settings are not retained after a power cycle Memory PresetCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment ControlsYou must enter a passcode to access the Service menu ServiceTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Logo LED setting Regardless of the Standby LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsScreen Commands Miscellaneous CommandsUsing Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit keyCommand Bits With Toggle Bit = Hex Binary Function StartRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerRC5 Data ST60MIN Using Hdmi CEC Messages CEC Commands Supported by the DHD ControllerOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control Specifications V-50HD/V-63HD SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications50HD Dimensions 1shows the V-50HD dimensions63HD Dimensions 2shows the V-63HD dimensionsSupported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 CompositeFormat Resolution Frequency Rate Hz MHz KHz RgbsPAL-M Specifications Page 020-1114-00 Rev. a April