Runco V-50HD You must enter a passcode to access the Calibration menu, Calibration ISF Settings

Page 53

Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Calibration menu.

Note

To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the Memory Presets menu (see page 38) or use the corresponding remote control buttons.

Display Color - Common Settings: Use the Display Color - Common Settings menu to adjust the color balance at the DHD Controller output. These settings are saved independently for each input and display mode.

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Gain for that color.

•Offset: Use the Offset controls to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Offset for that color.

•Gamma: Select Gamma from the Display Color - Common Settings menu to choose a de-gamma curve. Used correctly, the Gamma control can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas, lower the gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed out and unnatural, with excessive detail in black areas, increase the setting.

•Mode: With the V-50HD/V-63HD, two Gamma adjustment modes are available: Simple or Advanced. The two modes are mutually exclusive; when you select the Simple mode, the Advanced selection in the Gamma menu is grayed out. Likewise, when you select Advanced, the Simple selection is grayed out.

•Simple: Use the Simple Gamma control to perform gamma correction at the display according to a simple power law gamma function. The value chosen here corresponds to the power variable in this equation:

Output = InputPower

The DHD Controller applies this gamma curve to all three primary color channels (red, green and blue).

•Advanced: To select a custom gamma curve, select Mode from the Gamma menu and set it to Advanced. Then, select Advanced from the Gamma menu to select one of up to 20 pre-programmed gamma tables. Custom gamma tables provide the ability to perform complex, non-linear gamma correction on each primary color channel independently of the others.

Calibration

Calibration

ISF Settings

Display Color

Input Image

Input Color

Save ISF Night

Save ISF Day

Copy/Paste

Output Shift

Image Alignment

Splash Configure

OSD Position

Vistage™ Series Flat-Panel Display Installation/Operation Manual

41

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Specifications Maintenance and TroubleshootingOperation External ControlList of Figures List of Figures About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Controls and Functions IndicatorsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor Primary Input DHD Controller Front PanelDHD Controller Rear Panel Messages from the Hdmi Audio Out connectorDHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control UnitFor more information about aspect ratios, refer to Table LightCinema Controls and Functions Installation specialist InstallationRemote Control Installation Overview Quick SetupStep Procedure For Details, Refer OperationSynchronization Issues Installation ConsiderationsPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandOther Considerations Ambient LightRack-Mounting the DHD ControllerConnections to the V-50HD/V-63HD and DHD Controller Connecting the DHD Controller to the V-50HD/V-63HDUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workComponents to the DHD Connecting SourceComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Processor or Secondary Connecting an AudioDisplay Device to the DHD Controller OptionalEthernet Network RS-232 ControllerConnection Connecting to AC Power Turning on the PowerOperation Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusService Aspect Ratio Main MenuInput Source Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirNative Remote Aspect Ratio Control Description KeyPicture ScreenScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep TimerInformation SignalInformation SystemCalibration You must enter a passcode to access the Calibration menuCalibration ISF Settings Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copy/Paste Copied settings are not retained after a power cycleMemory Preset Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right MiddleTest Patterns and Their Suggested Usage You must enter a passcode to access the Service menuService Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation 38 and ISF Day/Night Memory Presets Regardless of the Logo LED settingRegardless of the Standby LED setting Operation Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Screen CommandsCommand Parameter min/max Value Stored? Description Using Discrete IR CodesEnter key Exit keyWith Toggle Bit = Hex Binary Function Start Command BitsRC5 Data Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller ST60MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications1shows the V-50HD dimensions 50HD Dimensions2shows the V-63HD dimensions 63HD DimensionsSupported Timings Supported Signal Timings by InputComponent Composite 1 Composite 2 CompositeRgbs Format Resolution Frequency Rate Hz MHz KHzPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents