Runco V-63HD, V-50HD operation manual Operation

Page 64

Operation

Color Space: Select Color Space from the Service menu to choose the color space of the source signal for HDMI, RGB, and component connections.

•The default setting, Auto, functions as follows:

•HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/or range data, the DHD Controller uses that information. Otherwise, for RGB sources, the DHD Controller uses the RGB-Videocolor space. For component SDTV and EDTV resolutions, REC601 is used. For other component video resolutions, REC709 is used.

•RGB: If Hsync or Vsync signals are present, the DHD Controller uses the RGB-PCcolor space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709 for all other sources.

•Component: For SDTV and EDTV resolutions, the DHD Controller uses the REC601 color space. For all other resolutions, REC709 is used.

In most cases, the Auto setting determines the correct color space to use. If it does not, you can force the DHD Controller to use a specific color space. Choose one of the following:

•REC709 sets the color space matrix to that defined in ITU-R BT.709.

•REC601 sets the color space matrix to that defined in ITU-R BT.601.

•RGB-PCuses RGB color space and sets black at 0,0,0 RGB and white at 255,255,255 RGB, assuming an 8-bit image.

•RGB-Videouses RGB color space and sets black at 16,16,16 RGB and white at 235,235,235, assuming an 8-bit image, to correspond to the luminance values defined in digital component standards.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language (English, Français, Deutsch, Italiano,

Español, Svenska, (Simplified Chinese), (Traditional Chinese),

Português, (Russian), (Japanese) or (Korean).

•OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer, which controls how long the menus remain on-screen after selecting them. Select from 5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want the menus to remain on-screen indefinitely.

•OSD Messages: When you select a new aspect ratio, input source or memory preset, the DHD Controller briefly displays an on-screen message confirming your new selection. To prevent the display of these messages, select OSD Messages from the Miscellaneous menu to and set it to Off.

•Blank Screen Color: Select Blank Screen Color from the Miscellaneous menu to select the color that appears when no incoming signal is present. The range is from 0 to 255 inclusive for each color component (red, green and blue).

•Sidebar Color: Select Sidebar Color from the Miscellaneous menu to change the color of the inactive image area. The range is from 0 to 255 inclusive for each color component (red, green and blue). The inactive image area is on either side of the active image area when using the 4:3 aspect ratio.

•Film Mode: Use Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the DHD Controller detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may want to enable Film Mode to ensure stable processing for that source.

52

Vistage™ Series Flat-Panel Display Installation/Operation Manual

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor DHD Controller Front Panel Primary InputMessages from the Hdmi Audio Out connector DHD Controller Rear PanelV-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote ControlLight For more information about aspect ratios, refer to TableCinema Controls and Functions Remote Control InstallationInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer OperationInstallation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandAmbient Light Other ConsiderationsRack-Mounting the DHD ControllerConnecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller OptionalConnection RS-232 ControllerEthernet Network Turning on the Power Connecting to AC PowerSetting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionService Input Source Main MenuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativeScreen PictureScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerSignal InformationInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment ControlsService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsScreen Commands Miscellaneous CommandsUsing Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit keyCommand Bits With Toggle Bit = Hex Binary Function StartRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications50HD Dimensions 1shows the V-50HD dimensions63HD Dimensions 2shows the V-63HD dimensionsSupported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 CompositeFormat Resolution Frequency Rate Hz MHz KHz RgbsPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents