Runco V-50HD, V-63HD operation manual High as is necessary to produce the desired brightness

Page 55

Operation

Table 4-2. Color Temperature Presets and Associated Color Points

Color Temperature Preset

Associated x/y Values

 

 

x

y

 

 

 

 

6500K

0.313

0.329

 

 

 

7500K

0.299

0.315

 

 

 

9300K

0.284

0.298

 

 

 

Display Color - Panel Settings: These settings are also saved independently for each input and display mode.

•Panel Brightness: The Panel Brightness control changes the apparent brightness of the displayed image. Its effect is similar to that of a lamp intensity control on a projector. Use a higher setting for rooms with a lot of ambient light. Use a lower setting for more “theater-like” viewing conditions (little or no ambient light).

Tip

To prolong the life of the display, set the Panel Brightness only as

high as is necessary to produce the desired brightness.

•Power Mode: Select Power Mode from the Display Color - Panel Settings menu to set

the power consumption threshold for the panel: High, Normal or Eco. The default setting is High.

Input Image: The Input Image controls are functionally similar to those in the Picture menu (refer to page 32), but are accessible only by entering the Calibration menu passcode.

The Input Image settings establish the “zero point” for the Picture

Note menu settings, whose values represent offsets from the Input Image settings. For example, if you set Brightness to 10 in this menu, setting Brightness to 10 in the Picture menu results in an actual setting value of 20 (10+10).

Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input and display mode.

•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls operate similarly to those in the Display Color - Common Settings menu (described on page 41), but affect the Y, Pb and Pr signal components rather than the red, green and blue channels.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a composite video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

Vistage™ Series Flat-Panel Display Installation/Operation Manual

43

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents External Control Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationDescription, Features and Benefits Optional Accessories Front-Panel Controls IndicatorsControls and Functions Vistage Series at a GlanceRemote Control Sensor Primary Input DHD Controller Front PanelDHD Controller Rear Panel Messages from the Hdmi Audio Out connectorDHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control UnitFor more information about aspect ratios, refer to Table LightCinema Controls and Functions Remote Control InstallationInstallation specialist Operation Quick SetupInstallation Overview Step Procedure For Details, ReferMounting the V-50HD/V-63HD on a Wall or Table Stand Installation ConsiderationsSynchronization Issues Possible Audio Latency for Various Input TimingsController Ambient LightOther Considerations Rack-Mounting the DHDDVI-to-HDMI adapters will not work Connecting the DHD Controller to the V-50HD/V-63HDConnections to the V-50HD/V-63HD and DHD Controller Use an Hdmi cable for this connection. a DVI cable withComponents to the DHD Connecting SourceComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Controller Optional Connecting an AudioProcessor or Secondary Display Device to the DHDConnection RS-232 ControllerEthernet Network Connecting to AC Power Turning on the PowerOperation Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusService Input Source Main MenuAspect Ratio Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsNative Remote Aspect Ratio Control Description KeyPicture ScreenPicture ScreenTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerSystem SignalInformation InformationCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right MiddleService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartTroubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Screen CommandsExit key Using Discrete IR CodesCommand Parameter min/max Value Stored? Description Enter keyWith Toggle Bit = Hex Binary Function Start Command BitsRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications1shows the V-50HD dimensions 50HD Dimensions2shows the V-63HD dimensions 63HD DimensionsComposite 1 Composite 2 Composite Supported Signal Timings by InputSupported Timings ComponentRgbs Format Resolution Frequency Rate Hz MHz KHzPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents