Runco V-63HD, V-50HD operation manual Information, Signal, System, Network

Page 52

Operation

Information ➤

Information

Signal

System

Network

Field Service

Signal / System: Select Information from the Main Menu, then choose either Signal or System to display information about the current input signal (resolution, frequency, type et cetera) and installed firmware versions, as well as other information that uniquely identifies your DHD Controller and display device.

Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues.

Manufacturing

	Signal
Input Source	HDMI 1
Signal Format	1080p/60
Input Resolution	1920x1080
Vertical Freq	59.94 Hz
Horizontal Freq	67.500 kHz
Pixel Clock	148.500 MHz
Color Space	REC709
Sync Type	Separate
Memory Preset	ISF Night

System

Model	DHD-LS
Display Name	V-50HD/V-63HD
Output Resolution	1920x1080
Serial Number	00000000
Boot Version	4.0
Firmware Version	4.0
Micro Version	4.0

Network

MAC Address	1A:2B:3C:4D:5E:6F
IP Address	192.168.0.150
Subnet Mask	255.255.0.0
Default Gateway	192.168.1.1
DHCP	Enabled
Network Status	Connected

Network: Select Information from the Main Menu, then choose Network to display information about the Ethernet network connection.

To enable network communication via Ethernet, refer to IP Configuration on page 48.

Field Service / Manufacturing: The Field Service and Manufacturing menus are password-protected and intended for use only by Runco service personnel and factory technicians.

40	Vistage™ Series Flat-Panel Display Installation/Operation Manual

Image 52

Contents Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor DHD Controller Front Panel Primary InputMessages from the Hdmi Audio Out connector DHD Controller Rear PanelV-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote ControlLight For more information about aspect ratios, refer to TableCinema Controls and Functions Remote Control InstallationInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer OperationInstallation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandAmbient Light Other ConsiderationsRack-Mounting the DHD ControllerConnecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller OptionalConnection RS-232 ControllerEthernet Network Turning on the Power Connecting to AC PowerSetting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionService Input Source Main MenuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativeScreen PictureScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerSignal InformationInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment ControlsService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsScreen Commands Miscellaneous CommandsUsing Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit keyCommand Bits With Toggle Bit = Hex Binary Function StartRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications50HD Dimensions 1shows the V-50HD dimensions63HD Dimensions 2shows the V-63HD dimensionsSupported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 CompositeFormat Resolution Frequency Rate Hz MHz KHz RgbsPAL-M Specifications Page 020-1114-00 Rev. a April