Runco V-50HD, V-63HD operation manual Remote Control, Installation specialist

Page 25

Installation

3. Installation

Note	Installation must be performed by a qualified custom video
	installation specialist.

To install batteries in the remote control:

1.Press down the tab on the cover and pull the cover in the direction of the

arrow.

2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place.

•Make sure that the battery polarities are correct when installing the batteries.

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

•Do not expose batteries to excessive heat such as from sunshine, fire or the like.

3.1

Remote Control

Notes on Batteries

Vistage™ Series Flat-Panel Display Installation/Operation Manual

13

Image 25

Contents Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Specifications Maintenance and TroubleshootingOperation External ControlList of Figures List of Figures About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Controls and Functions IndicatorsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor Primary Input DHD Controller Front PanelDHD Controller Rear Panel Messages from the Hdmi Audio Out connectorDHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control UnitFor more information about aspect ratios, refer to Table LightCinema Controls and Functions Remote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer OperationSynchronization Issues Installation ConsiderationsPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandOther Considerations Ambient LightRack-Mounting the DHD ControllerConnections to the V-50HD/V-63HD and DHD Controller Connecting the DHD Controller to the V-50HD/V-63HDUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workComponents to the DHD Connecting SourceComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Processor or Secondary Connecting an AudioDisplay Device to the DHD Controller OptionalConnection RS-232 ControllerEthernet Network Connecting to AC Power Turning on the PowerOperation Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusService Input Source Main MenuAspect Ratio Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirNative Remote Aspect Ratio Control Description KeyPicture ScreenScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerInformation SignalInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right MiddleService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Screen CommandsCommand Parameter min/max Value Stored? Description Using Discrete IR CodesEnter key Exit keyWith Toggle Bit = Hex Binary Function Start Command BitsRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications1shows the V-50HD dimensions 50HD Dimensions2shows the V-63HD dimensions 63HD DimensionsSupported Timings Supported Signal Timings by InputComponent Composite 1 Composite 2 CompositeRgbs Format Resolution Frequency Rate Hz MHz KHzPAL-M Specifications Page 020-1114-00 Rev. a April