Runco V-63HD Copied settings are not retained after a power cycle, Copy/Paste, Memory Preset

Page 56

Copy/Paste

Memory Preset

Aspect Ratio

Memory Preset

Copy Settings

Paste Settings

Copied From:

 

Input Source

HDMI 1

Signal Format

1080p/60

Memory Preset

ISF Night

Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this.

Copy/Paste - Memory Preset: You can copy and paste settings from one memory preset to another. This gives you a convenient starting point for creating a new preset based on an existing one, to make the calibration process less time-consuming.

For example, you can use the Copy/Paste Memory Preset feature to:

•Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.

•Calibrate an input for 720p source signals, then use those settings for 1080i sources.

•Duplicate ISF Night settings for a given source and signal format and save them in the Custom 1 memory preset.

To use this feature, select Copy/Paste from the Calibration menu, then select Memory Preset.

•Memory Preset - Copy Settings: Select Copy Settings from the Copy/Paste Memory Preset menu to place the settings for the current input source, signal format (resolution and frame rate) and memory preset onto a “clipboard,” which is a temporary memory location. When you do, the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied settings.

Copied settings are not retained after a power cycle.

Note

Copy/Paste

Memory Preset

Aspect Ratio

Aspect Ratio

Copy Settings

Paste Settings

Copied From:

 

Aspect Ratio

16:9

Screen

Screen 1

•Memory Preset - Paste Settings: To apply the settings on the clipboard to a different input source, signal format and/or memory preset, do any or all of the following:

•Switch to another input (for example, from HD1 to HD2).

•Change the output signal format at the source (for example, from 720p/60 to 1080i/60).

•Switch to another Memory Preset (for example, from ISF Night to Custom 1).

Then, select Paste Settings from the Copy/Paste Memory Preset menu. If you want to keep these new settings, you must save them! (Refer to Save ISF Night/Save ISF Day on page 44 or Memory Presets on page 38.)

Copy/Paste - Aspect Ratio: You can also copy and paste certain settings, such as those for Output Shift and Image Alignment (refer to page 45) from one aspect ratio or “screen” (refer to Screen on page 32) to another.

To do this, select Copy/Paste from the Calibration menu, then select Aspect Ratio.

•Aspect Ratio - Copy Settings: Select Copy Settings from the Copy/Paste Aspect Ratio menu to place the Output Shift and Image Alignment settings for the current aspect ratio onto a “clipboard,” which is a temporary memory location. When you do, the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied settings.

Copied settings are not retained after a power cycle.

Note

44

Vistage™ Series Flat-Panel Display Installation/Operation Manual

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor DHD Controller Front Panel Primary InputMessages from the Hdmi Audio Out connector DHD Controller Rear PanelV-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote ControlLight For more information about aspect ratios, refer to TableCinema Controls and Functions Installation specialist InstallationRemote Control Quick Setup Installation OverviewStep Procedure For Details, Refer OperationInstallation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandAmbient Light Other ConsiderationsRack-Mounting the DHD ControllerConnecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller OptionalEthernet Network RS-232 ControllerConnection Turning on the Power Connecting to AC PowerSetting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionService Aspect Ratio Main MenuInput Source Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativeScreen PictureScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep TimerSignal InformationInformation SystemCalibration You must enter a passcode to access the Calibration menuCalibration ISF Settings Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copy/Paste Copied settings are not retained after a power cycleMemory Preset Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment ControlsTest Patterns and Their Suggested Usage You must enter a passcode to access the Service menuService Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation 38 and ISF Day/Night Memory Presets Regardless of the Logo LED settingRegardless of the Standby LED setting Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsScreen Commands Miscellaneous CommandsUsing Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit keyCommand Bits With Toggle Bit = Hex Binary Function StartRC5 Data Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller ST60MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications50HD Dimensions 1shows the V-50HD dimensions63HD Dimensions 2shows the V-63HD dimensionsSupported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 CompositeFormat Resolution Frequency Rate Hz MHz KHz RgbsPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents