Runco V-63HD, V-50HD operation manual Grey Bars Input Names

Page 60

Operation

Table 4-3. Test Patterns and Their Suggested Usage

Pattern

Suggested Usage

Use this pattern when making brightness, contrast or white balance (gain/offset) adjustments.

Grey Bars

 

 

 

 

 

 

Input Names

 

 

 

 

 

 

 

 

 

Restore

 

 

 

 

 

 

 

 

C

o

mp o s i

t e

1

Composite 1

 

 

 

 

 

 

 

 

 

C

o mp o s i

t e

2

Composite 2

C

o

mp o s i

t e

3

Composite 3

C

o

mp

o n e n t

 

Component

H

D

1

 

 

 

 

 

HD 1

H

D

2

 

 

 

 

 

HD 2

S

C

A

R

T

 

 

 

 

SCART

H

D

M

I

 

1

 

 

 

HDMI 1

H

D

M

I

 

2

 

 

 

HDMI 2

H

D

M

I

 

3

 

 

 

HDMI 3

H

D

M

I

 

4

 

 

 

HDMI 4

 

 

 

 

 

 

 

 

 

 

Press MENU to exit test pattern mode.

Input Names: You can give each input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press

or to select a character to change. When you have finished editing the input name, press ENTER or MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

Display Device - Configure: The options in the Display Device - Configure menu allow you to change the picture orientation or access other, display-device specific functions.

•Installation – Orientation: Select Picture Orientation from the Display Device - Configure menu, then select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear). Or, use the Auto setting to have the display automatically determine the orientation (floor or ceiling) using an internal sensor.

•Diagnostics: Select Diagnostics from the Display Device - Configure menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

Network: The options in the Network menu allow you to configure the network communication features.

•IP Configuration: Select IP Configuration from the Network menu to either set the IP address, subnet mask and default gateway of the DHD Controller manually or obtain these settings automatically, from a DHCP (Dynamic Host Configuration Protocol) server. (Most broadband routers and gateways support DHCP.) You can also test the network connection from this menu.

48

Vistage™ Series Flat-Panel Display Installation/Operation Manual

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Vistage Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Indicators Controls and FunctionsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor DHD Controller Front Panel Primary InputMessages from the Hdmi Audio Out connector DHD Controller Rear PanelV-50HD/V-63HD Remote Control Unit DHD Controller/V-50HD/V-63HD Remote ControlLight For more information about aspect ratios, refer to TableCinema Controls and Functions Installation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer OperationInstallation Considerations Synchronization IssuesPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandAmbient Light Other ConsiderationsRack-Mounting the DHD ControllerConnecting the DHD Controller to the V-50HD/V-63HD Connections to the V-50HD/V-63HD and DHD ControllerUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Connecting an Audio Processor or SecondaryDisplay Device to the DHD Controller OptionalRS-232 Controller ConnectionEthernet Network Turning on the Power Connecting to AC PowerSetting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionService Main Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativeScreen PictureScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep TimerSignal InformationInformation SystemYou must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Copied settings are not retained after a power cycle Memory PresetCopy/Paste Keystone and Pincushion Distortion Left Middle y setting also controls the Right Middle Image Alignment ControlsYou must enter a passcode to access the Service menu ServiceTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Logo LED setting Regardless of the Standby LED setting38 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsScreen Commands Miscellaneous CommandsUsing Discrete IR Codes Command Parameter min/max Value Stored? DescriptionEnter key Exit keyCommand Bits With Toggle Bit = Hex Binary Function StartRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerRC5 Data ST60MIN Using Hdmi CEC Messages CEC Commands Supported by the DHD ControllerOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control Specifications V-50HD/V-63HD SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications50HD Dimensions 1shows the V-50HD dimensions63HD Dimensions 2shows the V-63HD dimensionsSupported Signal Timings by Input Supported TimingsComponent Composite 1 Composite 2 CompositeFormat Resolution Frequency Rate Hz MHz KHz RgbsPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents