Runco V-50HD, V-63HD Regardless of the Logo LED setting, Regardless of the Standby LED setting

Page 67

Operation

Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust the brightness of the front-panel LED status indicator.

Logo LED Segment (Blue)

Standby LED Segment (Yellow)

•Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the blue LED segment. The range is from 0 (off) to 31.

Note	During a firmware upgrade, this LED lights at full brightness
	regardless of the Logo LED setting.

•Standby LED: Select Standby LED from the Front Panel Brightness menu to change the behavior of the yellow LED segment. When set to ON, the LED lights amber when the system is in standby mode; otherwise, it is off. When set to OFF, the LED is always off.

Note	During a firmware upgrade, this LED lights at full brightness
	regardless of the Standby LED setting.

Auto Power Off: Select Auto Power Off from the Service menu to have the

V-50HD/V-63HD turn itself off after a period of inactivity (no source signal present).

•Enable: By default, Auto Power Off is disabled. To enable it, select Enable from the Auto Power Off sub-menu and set it to On.

•Hours: The default time-out period is eight (8) hours; the range is from 1 to 24 hours.

Standby Mode: Select Standby Mode from the Service menu to control the DHD

Controller’s power management feature.

•Choose Low Power (the default setting) to have the DHD Controller shut down completely when it is turned off. This conserves power but increases the amount of time required by the DHD Controller to start up when it is turned on.

•Fast Startup is a “quick-start” mode that keeps the DHD Controller running when it is turned off even though it appears to be in standby mode. This allows for much quicker startup times but consumes more power.

System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears. Select Yes to continue with the reset or select No to cancel.

This action is not undoable. Proceed with caution! Before you Caution perform a System Reset, save your “Custom” Memory Presets

(page 38) and ISF Day/Night Memory Presets (page 44).

Vistage™ Series Flat-Panel Display Installation/Operation Manual

55

Image 67

Contents Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents External Control Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationDescription, Features and Benefits Optional Accessories Front-Panel Controls IndicatorsControls and Functions Vistage Series at a GlanceRemote Control Sensor Primary Input DHD Controller Front PanelDHD Controller Rear Panel Messages from the Hdmi Audio Out connectorDHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control UnitFor more information about aspect ratios, refer to Table LightCinema Controls and Functions Remote Control InstallationInstallation specialist Operation Quick SetupInstallation Overview Step Procedure For Details, ReferMounting the V-50HD/V-63HD on a Wall or Table Stand Installation ConsiderationsSynchronization Issues Possible Audio Latency for Various Input TimingsController Ambient LightOther Considerations Rack-Mounting the DHDDVI-to-HDMI adapters will not work Connecting the DHD Controller to the V-50HD/V-63HDConnections to the V-50HD/V-63HD and DHD Controller Use an Hdmi cable for this connection. a DVI cable withComponents to the DHD Connecting SourceComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Controller Optional Connecting an AudioProcessor or Secondary Display Device to the DHDConnection RS-232 ControllerEthernet Network Connecting to AC Power Turning on the PowerOperation Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusService Input Source Main MenuAspect Ratio Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsNative Remote Aspect Ratio Control Description KeyPicture ScreenPicture ScreenTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerSystem SignalInformation InformationCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right MiddleService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartTroubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Screen CommandsExit key Using Discrete IR CodesCommand Parameter min/max Value Stored? Description Enter keyWith Toggle Bit = Hex Binary Function Start Command BitsRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications1shows the V-50HD dimensions 50HD Dimensions2shows the V-63HD dimensions 63HD DimensionsComposite 1 Composite 2 Composite Supported Signal Timings by InputSupported Timings ComponentRgbs Format Resolution Frequency Rate Hz MHz KHzPAL-M Specifications Page 020-1114-00 Rev. a April