Runco V-50HD, V-63HD operation manual Operation

Page 61

Operation

•DHCP: To enable the DHCP client in the DHD Controller, select DHCP from the IP Configuration menu and set it to On. With this setting, the DHD Controller’s IP address, subnet mask and default gateway are assigned by the local DHCP server.

To manually configure these values, set DHCP to Off.

The IP Address, Subnet Mask and Default Gateway items in the IP Note Configuration menu are disabled (grayed out) when DHCP is

enabled.

•IP Address: Select IP Address from the IP Configuration menu to manually configure the IP Address of the DHD Controller, as follows:

1.Press or to select the first, second, third or fourth byte of the address.

2.Press or to set the value of that byte. The range is from 0 to 255 inclusive.

3.Repeat Steps 1 and 2 for all four bytes of the address.

4.Press MENU when you have finished setting the address.

•Subnet Mask: Select Subnet Mask from the IP Configuration menu to manually configure the IP subnet mask. The procedure is similar to that for setting the IP address.

•Default Gateway: Select Default Gateway from the IP Configuration menu to manually configure the default IP gateway. The procedure is similar to that for setting the IP address.

•Communication Test: Select Communication Test from the IP Configuration menu to verify proper operation of the network communication link.

To start the test, select Start Test from the Communication Test menu. The DHD Controller displays the message “Performing Communication Test.” When the test completes, the DHD Controller displays either “Failed” (along with the error that occurred) or “Succeeded.”

•Auto Firmware Upgrade: Select Auto Firmware Upgrade from the Network menu to enable automatic detection of a newer version of the DHD Controller firmware. If one is found, you can configure the DHD Controller to install it automatically. These features make it easier to keep your DHD Controller firmware up-to-date.

•Auto Check For New Firmware: To have the DHD Controller automatically check for firmware updates at periodic intervals, select Auto Check for New Firmware from the Auto Firmware Upgrade menu and set it to On. If you prefer to do this manually, set it to Off and use the Check For New Firmware sub-menu (described below).

•Auto Perform Upgrade: If the “Auto Check For New Firmware” process determines that a newer firmware version than the one currently installed is available, you can have the DHD Controller automatically download and install it. To do this, select Auto Perform Upgrade from the Auto Firmware Upgrade menu and set it to On. The upgrade will occur the next time the DHD Controller is “power-cycled” (powered off, then on again).

If you prefer to do this manually, set it to Off. The DHD Controller will ask if you want to perform the upgrade the next time it is power-cycled.

•Check For New Firmware: To have the DHD Controller check for new firmware on demand (and perform an upgrade if it finds a new version), select Check For New Firmware from the Auto Firmware Upgrade menu. If the DHD Controller finds a new firmware version, select Yes to perform the upgrade or No to return to the previous menu.

Vistage™ Series Flat-Panel Display Installation/Operation Manual

49

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Vistage Series Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Product Disposal Table of Contents Specifications Maintenance and TroubleshootingOperation External ControlList of Figures List of Figures About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Controls and Functions IndicatorsVistage Series at a Glance Front-Panel ControlsRemote Control Sensor Primary Input DHD Controller Front PanelDHD Controller Rear Panel Messages from the Hdmi Audio Out connectorDHD Controller/V-50HD/V-63HD Remote Control V-50HD/V-63HD Remote Control UnitFor more information about aspect ratios, refer to Table LightCinema Controls and Functions Remote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer OperationSynchronization Issues Installation ConsiderationsPossible Audio Latency for Various Input Timings Mounting the V-50HD/V-63HD on a Wall or Table StandOther Considerations Ambient LightRack-Mounting the DHD ControllerConnections to the V-50HD/V-63HD and DHD Controller Connecting the DHD Controller to the V-50HD/V-63HDUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workComponents to the DHD Connecting SourceComponent Video Source Connections Rgbhv Source Connections Composite Video Source Connections Processor or Secondary Connecting an AudioDisplay Device to the DHD Controller OptionalConnection RS-232 ControllerEthernet Network Connecting to AC Power Turning on the PowerOperation Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusService Input Source Main MenuAspect Ratio Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirNative Remote Aspect Ratio Control Description KeyPicture ScreenScreen PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerInformation SignalInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Color Temperature Presets and Associated Color Points High as is necessary to produce the desired brightness Memory Preset Copied settings are not retained after a power cycleCopy/Paste Keystone and Pincushion Distortion Image Alignment Controls Left Middle y setting also controls the Right MiddleService You must enter a passcode to access the Service menuTest Patterns and Their Suggested Usage Grey Bars Input Names Operation If a Display Error Firmware Upgrade functions Operation Onoff Operation Regardless of the Standby LED setting Regardless of the Logo LED setting38 and ISF Day/Night Memory Presets Operation Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionTroubleshooting Chart Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Screen CommandsCommand Parameter min/max Value Stored? Description Using Discrete IR CodesEnter key Exit keyWith Toggle Bit = Hex Binary Function Start Command BitsRC5 Control Codes for the DHD Controller Remote Control With Toggle Description Button Name Bit =RC5 Data ST60MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control V-50HD/V-63HD Specifications SpecificationsV-50HD/V-63HD Specifications DHD Controller Specifications DHD Controller Specifications1shows the V-50HD dimensions 50HD Dimensions2shows the V-63HD dimensions 63HD DimensionsSupported Timings Supported Signal Timings by InputComponent Composite 1 Composite 2 CompositeRgbs Format Resolution Frequency Rate Hz MHz KHzPAL-M Specifications Page 020-1114-00 Rev. a April
Top Page Image Contents