Xerox ls 32270 Installation Procedure, Below follows the procedure for installing the Xerox LS

Page 10

Installation

Xerox LS 3270

Printer Cable:

The Xerox LS 3270 does not necessarily have to be plugged directly into the Centronics Input Port of your printer. An extention Centronics cable can be ordered for distance connection between the Xerox LS 3270 and your printer. This kit also contains a velcro tape to enable mounting on the side of a printer.

Order no. 999 020 030

2.2.2 Installation Procedure

Below follows the procedure for installing the Xerox LS 3270:

1.Make sure the printer power is turned OFF.

2.Plug the Centronics Output Port of the Xerox LS 3270 into the Centronics Input port of the printer and lock it with the bail locks.

3.Check that the rotary switch on the Xerox LS 3270 is in the correct position for the printer driver needed:

Position A for PCL (default)

Position B for FSL

If you need to make changes to the printer driver, see section 1.1.1, PCL or FSL output Driver, “Changing the Driver”, for details on how to do this.

4.Connect the coax cable to the Xerox LS 3270.

5.Power ON the printer. The CU and PAR LEDs of the Xerox LS 3270 will turn on if the power is sufficient (for location of CU and PAR LEDs, see figure 2-1 in Section 2.1 Knowing the Front Panel).

6.Check power and signal connection. If po wer is sufficient and a coax connection exists between the Xerox LS 3270 and a controller, the green CU LED will stay ON. If the CU and PAR LEDs were not turned on at power on, you must add an external power supply to the Xerox LS 3270.

5.Send a job from the host system and check the printout. Note that the system printer emulation must match the Xerox LS 3270 printer driver. If not, change the printer driver

- 10 -

Image 10
Contents Rank Xerox Electronic Documentation Related Manuals PrefaceSeptember Table of Contents Introduction to the Xerox LS What is the Xerox LS 3270?PCL Driver Default PCL or FSL output driverXerox LS 3270 Features Changing the DriverInstallation Requirements Supported Control UnitsPaper Size Default US/EU Operating EnvironmentInstallation of the Xerox LS Knowing the Front PanelPre-Installation Information InstallationPrinter Dependency Installation Procedure Below follows the procedure for installing the Xerox LSAutomatic Power Supply Control Xerox LS 3270 and its side panelTesting PCL driverTimeout CU Contact with Control Unit Indicators of the Xerox LSOperation of the Xerox LS PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode Where % is the defined ESC character ESC FeaturesWhere % is the defined ESC character Send Logo Engineering Functions User Settings Functions X-FunctionsTest functions T-Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions FSL Setup via Xerox LS 3270 Parallel Port ??%%Y100,10,’SHARESTRING’%%X1Activating the Y249 Engineering Function Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating firmware Error Messages Recoverable ErrorsThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors Test Printouts Busy Timeout Timeout CoaxPCL Test Printout Proportional Spaced = Active Gfid =Busy Timeout FSL Test PrintoutLPI Appendix A. Quick Reference Guide to FSL FunctionsFSL N/S LPI FSL N/SEbcdic Y10 Y12 Y19 Y13Are wrapped Y22Name Syntax Parameters Deviations Y35 Y39 EABY41 IRQ Y47EEPROM/RAM ESCEeprom Y53 Y52Y54 Y59 Y55Y56 Y60Y74 Y71HEX Ascii HEX PCL modeFSL mode N2dataY79 APLName Syntax Parameters Deviations Y93 Y91Y92 Y94APO Y96Y98 Y110Y112 Y111Y113 Y115 Y114Y119 RAM Re. T2Data Appendix B. Selected Xerox Products Coax Supported Printers ExternalIndex Coax