Xerox ls 32270 instruction manual Xerox LS 3270 Features, Changing the Driver

Page 5

Introduction

Xerox LS 3270

Changing the Driver

To change from PCL to FSL driver or vice versa, first of all the rotary switch has to be in position T at power on. The current printer driver will be indicated on a printout. The actual selection of printer driver is then made by turning the rotary switch to position A (PCL) or B (FSL). The new position will also be indicated on a second printout. When the correct position is obtained, turn the rotary switch away from the A, B or T positions (any other position will do). The new driver is now active.

1.2. Xerox LS 3270 Features

The Xerox LS 3270 protocol converter gives you the following fea- tures:

IBM 3287, 32681 and 4214 emulations

Support of the SCS (LU1) and 3270 data stream (LU0 or LU3) modes including FMH data streams as required by the host system.

All IBM RPQs

Parallel output in PCL mode

Up to 8 user strings of variable length can be transmit ted to the printer from the Xerox LS 3270 - automatically at power on and before and after Local Copy from the host system.

Automatic input sharing between Coax and Centronics input ports.

Coax FSL setup via share port

Flash prom allowing downloading of new firmware via the coax or the centronics port.

Support of ida PSS

Autoconfiguration (PCL only)

13268 = factory default

- 5 -

Image 5
Contents Rank Xerox Electronic Documentation September PrefaceRelated Manuals Table of Contents PCL Driver Default What is the Xerox LS 3270?Introduction to the Xerox LS PCL or FSL output driverChanging the Driver Xerox LS 3270 FeaturesSupported Control Units Installation RequirementsOperating Environment Paper Size Default US/EUKnowing the Front Panel Installation of the Xerox LSPrinter Dependency InstallationPre-Installation Information Below follows the procedure for installing the Xerox LS Installation ProcedureXerox LS 3270 and its side panel Automatic Power Supply ControlPCL driver TestingTimeout Operation of the Xerox LS Indicators of the Xerox LSCU Contact with Control Unit PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode Where % is the defined ESC character Send Logo ESC FeaturesWhere % is the defined ESC character Test functions T-Functions User Settings Functions X-FunctionsEngineering Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox LS 3270 Parallel PortDeactivating the Y249 Engineering Function Limitations when Y249 is activeActivating the Y249 Engineering Function Updating firmware Recoverable Errors Error MessagesThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors PCL Test Printout Busy Timeout Timeout CoaxTest Printouts Active Gfid = Proportional Spaced =FSL Test Printout Busy TimeoutFSL N/S Appendix A. Quick Reference Guide to FSL FunctionsLPI LPI FSL N/SEbcdic Y10 Y12 Are wrapped Y13Y19 Y22Name Syntax Parameters Deviations Y35 Y41 EABY39 Y47 IRQEeprom ESCEEPROM/RAM Y54 Y52Y53 Y56 Y55Y59 Y60HEX Y71Y74 FSL mode PCL modeAscii HEX N2dataAPL Y79Name Syntax Parameters Deviations Y92 Y91Y93 Y94Y98 Y96APO Y110Y113 Y111Y112 Y119 Y114Y115 Data Re. T2RAM Coax Supported Printers External Appendix B. Selected Xerox ProductsCoax Index