Xerox ls 32270 instruction manual PCL mode, Ascii HEX, FSL mode, N2data, Y76

Page 46

Appendix A

Xerox LS 3270

No.

Name

Syntax

Parameters

Deviations

75

Overwrite

PCL:

n1

PCL mode

 

Translate

%Y75,<n1>[,n2],

00-BF = LU3 position

 

 

Table

<data>[:n1,n2,

in HEX of

 

 

 

<data>]%

character to

 

 

 

 

be trans-

 

 

 

 

lated

 

 

 

 

n2

 

 

 

 

1-8 = Symbol set

 

 

 

 

defined in FSL

 

 

 

 

74

 

 

 

 

n3

 

 

 

 

00-FF = Data in

 

 

 

 

ASCII HEX

 

 

 

 

required to

 

 

 

 

print the

 

 

 

 

character

 

 

 

-----------------

---------------------

--------

 

 

FSL:

n1

FSL mode

 

 

%Y75,n1,n2[;n2]

LU3 char.

 

 

 

[:n1,n2]%

00-BF =

 

 

 

 

Specifies which LU3

 

 

 

 

characters to be

 

 

 

 

translated to

 

 

 

 

parameter n2

 

 

 

 

n2(data)

 

 

 

 

00-FF =

 

 

 

 

ASCII code as the LU3

 

 

 

 

value shall be

 

 

 

 

translated to. Can be

 

 

 

 

defined as paired HEX

 

 

 

 

up to 12 bytes,

 

 

 

 

separated with

 

 

 

 

commas.

 

76

Create APL

%Y76,<n1>%

1-8 = Create an APL

Y76:

 

Translate

 

Translate Table

FSL only

 

Table

 

 

 

77

Reset APL

%Y77,<n1>%

1-8 = Reset the

 

 

Translate

 

indicated APL

 

 

Table

 

table

 

78

Select APL

%Y78,<n1>%

1-8 = Select the

 

 

Translate

 

indicated APL

 

 

Table

 

table

 

- 46 -

Image 46
Contents Rank Xerox Electronic Documentation Related Manuals PrefaceSeptember Table of Contents Introduction to the Xerox LS What is the Xerox LS 3270?PCL Driver Default PCL or FSL output driverXerox LS 3270 Features Changing the DriverInstallation Requirements Supported Control UnitsPaper Size Default US/EU Operating EnvironmentInstallation of the Xerox LS Knowing the Front PanelPre-Installation Information InstallationPrinter Dependency Installation Procedure Below follows the procedure for installing the Xerox LSAutomatic Power Supply Control Xerox LS 3270 and its side panelTesting PCL driverTimeout CU Contact with Control Unit Indicators of the Xerox LSOperation of the Xerox LS PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode Where % is the defined ESC character ESC FeaturesWhere % is the defined ESC character Send Logo Engineering Functions User Settings Functions X-FunctionsTest functions T-Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions FSL Setup via Xerox LS 3270 Parallel Port ??%%Y100,10,’SHARESTRING’%%X1Activating the Y249 Engineering Function Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating firmware Error Messages Recoverable ErrorsThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors Test Printouts Busy Timeout Timeout CoaxPCL Test Printout Proportional Spaced = Active Gfid =Busy Timeout FSL Test PrintoutLPI Appendix A. Quick Reference Guide to FSL FunctionsFSL N/S LPI FSL N/SEbcdic Y10 Y12 Y19 Y13Are wrapped Y22Name Syntax Parameters Deviations Y35 Y39 EABY41 IRQ Y47EEPROM/RAM ESCEeprom Y53 Y52Y54 Y59 Y55Y56 Y60Y74 Y71HEX Ascii HEX PCL modeFSL mode N2dataY79 APLName Syntax Parameters Deviations Y93 Y91Y92 Y94APO Y96Y98 Y110Y112 Y111Y113 Y115 Y114Y119 RAM Re. T2Data Appendix B. Selected Xerox Products Coax Supported Printers ExternalIndex Coax