Xerox ls 32270 instruction manual Setup Functions supported in FSL mode

Page 21

Programming the Xerox LS 3270

Xerox LS 3270

5.2. Setup Functions supported in FSL mode

Y1 Set IBM Buffer Size (parameters 2,3,4 & 5)

Y2 Set Default LPI (parameters 6 & 8)

Y3 Set Default CPI (parameters: 10, 12, 15 & 16)

Y5 Set Default Page Length (MPL)

Y6 Set Default Max. Print Position (MPP)

Y7 Set Case (Mono,Dual)

Y8 Set LU1 Language

Y9 Set Default Print Quality (parameters 2 & 3)

Y11 Set Default Paper Path (parameters 1, 2 & 3)

Y14 Enable Graphics Option (idaAFP) (parameters 0 & 1)

Y25 FF Before Local Copy

Y26 FF After Local Copy

Y27 NON-SCS Print Image

Y28 NON-SCS, CR at MPP+1

Y29 NON-SCS, NL at MPP+1

Y30 NON-SCS, Valid FF Followed by data

Y31 NON-SCS, Valid FF at end of buffer

Y32 NON-SCS, FF Valid

Y33 NON-SCS, Automatic Func. at end of job

Y34 Last LF on page sent as FF

Y35 FF from system sent as FF or LF's

Y36 Suppress IBM control codes

Y37 IBM Printer Emulation Select

Y38 IBM Communication Feature (Query, EAB)

Y39 Suppress Empty Forms

Y44 Suppress CR and SP

Y46 Set IRQ Timer

Y48 Set Permanent ESC Character

Y49 Restrict access of EEPROM settings

Y50 FF After Time Elapse

Y51 User-defined string(s) at Power-on

Y52 User-defined string(s) at Printer Power down/ Printer Error

Y53 User-defined string before Error M essage

Y54 User-defined string after Error Message

Y55 Barcode type select

Y56 Barcode Entry

Y57 User-defined string before local copy

Y58 User-defined string after local copy

Y61 Setup for user-defined strings

Y62 Setup for IBM defined strings

Y63 Define Logo

Y71 Create Translate Table

Y72 Reset Translate Table

- 21 -

Image 21
Contents Rank Xerox Electronic Documentation Preface Related ManualsSeptember Table of Contents PCL Driver Default What is the Xerox LS 3270?Introduction to the Xerox LS PCL or FSL output driverChanging the Driver Xerox LS 3270 FeaturesSupported Control Units Installation RequirementsOperating Environment Paper Size Default US/EUKnowing the Front Panel Installation of the Xerox LSInstallation Pre-Installation InformationPrinter Dependency Below follows the procedure for installing the Xerox LS Installation ProcedureXerox LS 3270 and its side panel Automatic Power Supply ControlPCL driver TestingTimeout Operation of the Xerox LS Indicators of the Xerox LSCU Contact with Control Unit PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode ESC Features Where % is the defined ESC characterWhere % is the defined ESC character Send Logo Test functions T-Functions User Settings Functions X-FunctionsEngineering Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox LS 3270 Parallel PortLimitations when Y249 is active Activating the Y249 Engineering FunctionDeactivating the Y249 Engineering Function Updating firmware Recoverable Errors Error MessagesThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors Busy Timeout Timeout Coax Test PrintoutsPCL Test Printout Active Gfid = Proportional Spaced =FSL Test Printout Busy TimeoutFSL N/S Appendix A. Quick Reference Guide to FSL FunctionsLPI LPI FSL N/SEbcdic Y10 Y12 Are wrapped Y13Y19 Y22Name Syntax Parameters Deviations Y35 EAB Y39Y41 Y47 IRQESC EEPROM/RAMEeprom Y52 Y53Y54 Y56 Y55Y59 Y60Y71 Y74HEX FSL mode PCL modeAscii HEX N2dataAPL Y79Name Syntax Parameters Deviations Y92 Y91Y93 Y94Y98 Y96APO Y110Y111 Y112Y113 Y114 Y115Y119 Re. T2 RAMData Coax Supported Printers External Appendix B. Selected Xerox ProductsCoax Index