Xerox ls 32270 instruction manual Programming theXerox LS, PCL Driver Default

Page 17

Programming the Xerox LS 3270

Xerox LS 3270

5. Programming theXerox LS 3270

The Xerox LS 3270 supports approximately 60 internal Setup Functions (FSL Functions) 4. When the protocol converter has been installed and connected to a printer, you may have to consider the use of these setup options.

FSL setup functions can be sent either from your IBM system or from a PC.

PCL Driver (Default)

If you have decided to run the Xerox LS 3270 in PCL mode (see Chapter 1), the Xerox LS 3270 is ready to operate after you have completed the installation procedure. The factory default setup will meet the demands of most host systems and users, and special programming is therefore normally not required.

However, special circumstances may require changes in the programming of the box. For full details on this please see the " 3270 Programmer's Guide" Document no. D62077. In the Programmer's Guide you will find an extensive description of the FSL Functions with notes, comments and examples.

FSL Driver

If you have decided to run the Xerox LS 3270 in FSL mode (see Chapter 1), you have just selected an unprogrammed printer driver and you need to program any further settings of the box using FSL functions. The " 3270 Programmer's Guide" Document no. D62077, gives you full details on how you do this.

On the following pages you will find a list of the functions available in PCL mode and FSL mode respectively.

4FSL = Function Selection via the Line

- 17 -

Image 17
Contents Rank Xerox Electronic Documentation September PrefaceRelated Manuals Table of Contents PCL Driver Default What is the Xerox LS 3270?Introduction to the Xerox LS PCL or FSL output driverChanging the Driver Xerox LS 3270 FeaturesSupported Control Units Installation RequirementsOperating Environment Paper Size Default US/EUKnowing the Front Panel Installation of the Xerox LSPrinter Dependency InstallationPre-Installation Information Below follows the procedure for installing the Xerox LS Installation ProcedureXerox LS 3270 and its side panel Automatic Power Supply ControlPCL driver TestingTimeout Operation of the Xerox LS Indicators of the Xerox LSCU Contact with Control Unit PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode Where % is the defined ESC character Send Logo ESC FeaturesWhere % is the defined ESC character Test functions T-Functions User Settings Functions X-FunctionsEngineering Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox LS 3270 Parallel PortDeactivating the Y249 Engineering Function Limitations when Y249 is activeActivating the Y249 Engineering Function Updating firmware Recoverable Errors Error MessagesThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors PCL Test Printout Busy Timeout Timeout CoaxTest Printouts Active Gfid = Proportional Spaced =FSL Test Printout Busy TimeoutFSL N/S Appendix A. Quick Reference Guide to FSL FunctionsLPI LPI FSL N/SEbcdic Y10 Y12 Are wrapped Y13Y19 Y22Name Syntax Parameters Deviations Y35 Y41 EABY39 Y47 IRQEeprom ESCEEPROM/RAM Y54 Y52Y53 Y56 Y55Y59 Y60HEX Y71Y74 FSL mode PCL modeAscii HEX N2dataAPL Y79Name Syntax Parameters Deviations Y92 Y91Y93 Y94Y98 Y96APO Y110Y113 Y111Y112 Y119 Y114Y115 Data Re. T2RAM Coax Supported Printers External Appendix B. Selected Xerox ProductsCoax Index