Xerox ls 32270 instruction manual Setup functions supported in PCL mode

Page 18

Programming the Xerox LS 3270

Xerox LS 3270

5.1. Setup functions supported in PCL mode

Y1	Set IBM Buffer Size
Y2	Set Default LPI
Y3	Set Default CPI
Y4	Set Default Line Spacing
Y5	Set Default Page Length (MPL)
Y6	Set Default Max. Print Position (MPP)
Y7	Set Case (Mono,Dual)
Y8	Set LU1 Language
Y10	Set Page Format
Y11	Set Default Paper Path
Y12	Set Default Paper Size
Y13	Line Overflow Condition
Y14	Enable Graphics Option (idaAFP)
Y19	Set Simplex/Duplex
Y22	Printer Driver Selection
Y25	FF Before Local Copy
Y26	FF After Local Copy
Y27	NON-SCS Print Image
Y28	NON-SCS, CR at MPP+1
Y29	NON-SCS, NL at MPP+1
Y30	NON-SCS, Valid FF Followed by data
Y31	NON-SCS, Valid FF at end of buffer
Y32	NON-SCS, FF Valid
Y33	NON-SCS, Automatic Func. at end of job
Y34	Last LF on page sent as FF
Y36	Suppress IBM control codes (parameters 0 and 1)
Y37	IBM Printer Emulation Select (parameters 0,1,2 & 4)
Y38	IBM Communication Feature (Query, EAB)
Y41	Generation of NL at EM
Y44	Suppress CR and SP
Y46	Set IRQ Timer
Y47	ESC Mode Selection
Y48	Set Permanent ESC Character
Y49	Restrict access of NVRAM settings
Y50	FF After Time Elapse
Y51	User-defined string(s) at Power-on
Y57	User-defined string before local copy
Y58	User-defined string after local copy
Y59	Bar Code Type Definition
Y60	Font Link
Y61	Setup for user-defined strings (parameters 0 - 7)
Y62	Setup for IBM defined strings
Y63	Define Logo
Y72	Reset Translate Table
Y73	Select Translate Table

- 18 -

Image 18

Contents Rank Xerox Electronic Documentation Preface Related ManualsSeptember Table of Contents Introduction to the Xerox LS What is the Xerox LS 3270?PCL Driver Default PCL or FSL output driverXerox LS 3270 Features Changing the DriverInstallation Requirements Supported Control UnitsPaper Size Default US/EU Operating EnvironmentInstallation of the Xerox LS Knowing the Front PanelInstallation Pre-Installation InformationPrinter Dependency Installation Procedure Below follows the procedure for installing the Xerox LSAutomatic Power Supply Control Xerox LS 3270 and its side panelTesting PCL driverTimeout CU Contact with Control Unit Indicators of the Xerox LSOperation of the Xerox LS PAR Parallel inputSpecifying Timeout 3NVRAM = Non-volatile RAM Programming theXerox LS Setup functions supported in PCL mode ESC Features Where % is the defined ESC characterWhere % is the defined ESC character Send Logo Engineering Functions User Settings Functions X-FunctionsTest functions T-Functions FunctionsSetup Functions supported in FSL mode ESC Features User Settings Functions X-Functions FSL Setup via Xerox LS 3270 Parallel Port ??%%Y100,10,’SHARESTRING’%%X1Limitations when Y249 is active Activating the Y249 Engineering FunctionDeactivating the Y249 Engineering Function Updating firmware Error Messages Recoverable ErrorsThere is no Space Left Dynamic Area Non-Recoverable Hardware Errors Busy Timeout Timeout Coax Test PrintoutsPCL Test Printout Proportional Spaced = Active Gfid =Busy Timeout FSL Test PrintoutLPI Appendix A. Quick Reference Guide to FSL FunctionsFSL N/S LPI FSL N/SEbcdic Y10 Y12 Y19 Y13Are wrapped Y22Name Syntax Parameters Deviations Y35 EAB Y39Y41 IRQ Y47ESC EEPROM/RAMEeprom Y52 Y53Y54 Y59 Y55Y56 Y60Y71 Y74HEX Ascii HEX PCL modeFSL mode N2dataY79 APLName Syntax Parameters Deviations Y93 Y91Y92 Y94APO Y96Y98 Y110Y111 Y112Y113 Y114 Y115Y119 Re. T2 RAMData Appendix B. Selected Xerox Products Coax Supported Printers ExternalIndex Coax