JVC HR-S9600EU specifications Recording, Playback, Or press Record on the recorder

Page 27

Recording

1	START RECORDING
	Press and hold RECORD and press PLAY on the remote,
	or press RECORD on the recorder.
	DURING B.E.S.T.

B.E.S.T. COMPLETE

●The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.

NOTES:

●The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●The B.E.S.T. system does not work while Auto Satellite Prog recording is in progress (☞ pg. 35).

●In the case of timer recording, the B.E.S.T. system works before recording is initiated.

●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed.

●Pressing the recorder's RECORD button while "BEST" is displayed does not start Instant Timer Recording (☞ pg. 23).

ATTENTION

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

1)Press and hold PAUSE and press RECORD to engage the RECORD PAUSE mode.

●The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE.

2)Press PLAY to start recording.

●If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 4 on page 26.

EN27

Playback

The recorder assesses the quality of the tape once you initiate playback.

START PLAYBACK

1 Press PLAY.

●The recorder adjusts the playback picture quality based on the quality of the tape in use.

●B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel.

NOTES:

●When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

●When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference by performing steps 1 through 5 on page 26.

●"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.

Image 27

Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderVideo Connection Connect Recorder to TVBack of Recorder If you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelLanguage Code Preset Download Just Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage 13 14 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenSAVE, then press OK or #to set to on Power Save ModeMode SET, then press OK or #NexTView Link TV Auto Power OnLink Functions LI NKPress %Þ to move the highlight bar pointer to Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointPlayback Features PlaybackActivate HIGH-SPEED Search Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyDigital TBC/NR Digital 3RSoundtrack Selection Activate Instant ReviewRepeat Playback Instant ReViewTimeScan Audio signal during TimeScanTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features VHS Super VHS and VHS Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingAdjust Audio Control ScreenRecording Level S.T. Picture System EN RecordingPreparation Recording PlaybackOr press Record on the recorder EN Timer Recording Timer ProgrammingTimer Warning ÄTIMER indicatorSatellite Tuner Users Express Timer Programming Before performing Express Timer ProgrammingTime Engage RECORDER’S SET VPS/PDC ModeTimer Mode Return to NormalTE+ Check, Cancel And Replace ProgrammesThen press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #On or OFF Auto TimerAuto TIMER, then press OK or #to select eitherProg REC Mode Automatic Satellite Programme RecordingBefore performing the following steps Code Remote Control FunctionsSET Remote Control RE-SUPPLY PowerOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeOperate Satellite Tuner EN Special FeaturesSatellite Tuner Multi-Brand Remote Control SET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEditing If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderRecorder Player Connector Lanc Cable not provided To Lanc connectorSynchro Editing Repeat steps 4 6 as necessaryEdit To Or From Another Video Recorder Your recorder TV Receiver Pin Scart Cable NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorderAV2 Select Setting AV1 Select SettingEND Audio Dubbing SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Insert EditingPress Insert Engage Insert EditingStart Editing END Insert EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditSET Jlip ID Number Access Main Menu ScreenAccess Initial SET Screen Access Jlip ID NO. SET ScreenSimple Connections Connection ToTuner System ConnectionsSatellite Tuner Unit Connector ScartEN System Connections Perfect ConnectionsDecoder ConnectorBasic Connections Back of Recorder Mains outletSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderConnecting Using a Stereo System Speaker Television Mains outletRear View Auto Channel Set Access Auto CH SETTuner Set EN Subsi Diary Sett IngsView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetSET Date and Time Access Initial SETClock Set Turn the Recorder onStart Clock Operation SET Just ClockGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD PAL-type colour signal and Ccir Provided accessoriesSpeci Fications Ex. Deutschland is selected Ex. Francais is selected for BelgiumInternational Telephone Language Code