JVC HR-S9600EU Basic Playback, Load a Cassette, Point, Start Playback, Stop Playback

Page 15

PLAYBACK

EN15

Basic

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

STOP/EJECT

8

13

2

PLAY

SHUTTLE

1	3
2

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

	1		LOAD A CASSETTE
		Make sure the window side is up, the rear label side is
			facing you and the arrow on the front of the cassette is
			pointed toward the recorder. Don’t apply too much
			pressure when inserting.

			● The recorder power comes on automatically and the
			counter is reset to 0:00:00.
			● If the record safety tab has been removed, playback
			begins automatically.

			FIND PROGRAMME START
	2		POINT
		If the tape is advanced past the start point, press REW or
			turn the SHUTTLE ring to the left.
			To go forward, press FF or turn the SHUTTLE ring to the
			right.

	3		START PLAYBACK
		Press PLAY. “BEST” appears blinking in the recorder's
			display panel during automatic tracking. (☞ pg. 26)
	4		STOP PLAYBACK
		Press STOP on the remote or STOP/EJECT on the
			recorder’s front panel. Then press STOP/EJECT to
			remove the cassette.

P

LAY

FF

REW

	P
	O
T
S

Tape Position Indicator

Usable cassettes

● Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0”

(beginning) or “+” (end) 0 + shows you where you are

on the tape.

”O.S.D.” (☞ pg. 11) must

be set to “ON”, or the Beginning indicator will not appear.

3

+ +

1:23:45 REMAIN 2:35

End

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

● This video recorder can record on regular VHS and

Super VHS cassettes. While only VHS signals can be

recorded on regular VHS cassettes, both VHS and Super

VHS signals can be recorded and played back using

Super VHS cassettes.

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Image 15

Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderVideo Connection Connect Recorder to TVBack of Recorder If you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelLanguage Code Preset Download Just Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage 13 14 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal Screen SAVE, then press OK or #to set to on Power Save Mode Mode SET, then press OK or #NexTView Link TV Auto Power OnLink Functions LI NKPress %Þ to move the highlight bar pointer to Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointPlayback Features PlaybackActivate HIGH-SPEED Search Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyDigital TBC/NR Digital 3RSoundtrack Selection Activate Instant ReviewRepeat Playback Instant ReViewTimeScan Audio signal during TimeScanTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features VHS Super VHS and VHS Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingAdjust Audio Control ScreenRecording Level S.T. Picture System EN RecordingPreparation Recording PlaybackOr press Record on the recorder EN Timer Recording Timer ProgrammingTimer Warning ÄTIMER indicatorSatellite Tuner Users Express Timer Programming Before performing Express Timer ProgrammingTime Engage RECORDER’S SET VPS/PDC ModeTimer Mode Return to NormalTE+ Check, Cancel And Replace ProgrammesThen press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #On or OFF Auto TimerAuto TIMER, then press OK or #to select eitherProg REC Mode Automatic Satellite Programme RecordingBefore performing the following steps Code Remote Control FunctionsSET Remote Control RE-SUPPLY PowerOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeOperate Satellite Tuner EN Special FeaturesSatellite Tuner Multi-Brand Remote Control SET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEditing If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderRecorder Player Connector Lanc Cable not provided To Lanc connectorSynchro Editing Repeat steps 4 6 as necessaryEdit To Or From Another Video Recorder Your recorder TV Receiver Pin Scart Cable NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorderAV2 Select Setting AV1 Select SettingEND Audio Dubbing SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Insert EditingPress Insert Engage Insert EditingStart Editing END Insert EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditSET Jlip ID Number Access Main Menu ScreenAccess Initial SET Screen Access Jlip ID NO. SET ScreenSimple Connections Connection ToTuner System ConnectionsSatellite Tuner Unit Connector ScartEN System Connections Perfect ConnectionsDecoder ConnectorBasic Connections Back of Recorder Mains outletSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderConnecting Using a Stereo System Speaker Television Mains outletRear View Auto Channel Set Access Auto CH SETTuner Set EN Subsi Diary Sett IngsView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetSET Date and Time Access Initial SETClock Set Turn the Recorder onStart Clock Operation SET Just ClockGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD PAL-type colour signal and Ccir Provided accessoriesSpeci Fications Ex. Deutschland is selected Ex. Francais is selected for BelgiumInternational Telephone Language Code