JVC HR-S9600EU Quest Ions and Answers, Ä remain lit on the display panel. Is there Problem?

Page 69

QUESTIONSANDANSWERS

EN69

PLAYBACK

 

TIMER RECORDING

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder goes to its Stop mode automatically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning.

Q. "" and "ä" remain lit on the display panel. Is there

aproblem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the programme or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 69
Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsVideo Connection Connect Recorder to TVBack of Recorder EN Initial Settings Auto Set UpIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Preset Download Language for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage On-Screen Displays ENABLE/DISABLE ON-SCREEN DisplayReturn to Normal Screen 13 14Mode SET, then press Power Save ModeOK or # SAVE, then press OK or #to set to onLink Functions TV Auto Power OnLI NK NexTView LinkMode Colour System SetAbout Ntsc Playback Press %Þ to move the highlight bar pointer toLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Features PlaybackActivate HIGH-SPEED Search Override Automatic Tracking Adjust TrackingManually Return to AutomaticDigital TBC/NR Digital 3RRepeat Playback Activate Instant ReviewInstant ReView Soundtrack SelectionTimeScan Audio signal during TimeScanTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features Locate Start Point Engage RECORD-PAUSE ModeResume Recording VHS Super VHS and VHSAdjust Audio Control ScreenRecording Level S.T. Picture System EN RecordingPreparation Recording PlaybackOr press Record on the recorder EN Timer Recording Timer ProgrammingTimer Warning ÄTIMER indicatorSatellite Tuner Users Express Timer Programming Before performing Express Timer ProgrammingTime Timer Mode SET VPS/PDC ModeReturn to Normal Engage RECORDER’STE+ Check, Cancel And Replace ProgrammesFor Example Auto SP→LP TimerSET, then press OK or # Then press OK or #to selectAuto TIMER, then press Auto TimerOK or #to select either On or OFFProg REC Mode Automatic Satellite Programme RecordingBefore performing the following steps SET Remote Control Remote Control FunctionsRE-SUPPLY Power CodeControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSatellite Tuner Multi-Brand Remote Control EN Special FeaturesSET Satellite Tuner Brand Code Operate Satellite TunerControl SET Mode Access Mode SETPreparation For Editing Select PictureIf the camcorder has an S-VIDEO output connector Recorder If the camcorder has no S-VIDEO output connector RecorderEdit From Camcorder EditingSynchro Editing Connector Lanc Cable not provided To Lanc connectorRepeat steps 4 6 as necessary Recorder PlayerEdit To Or From Another Video Recorder TV Receiver NEL or Or AV Provided AV mode Mode Another recorderYour recorder Your recorder TV Receiver Pin Scart CableAV2 Select Setting AV1 Select SettingEngage Audio Dubbing SET Input ModeStart Dubbing END Audio DubbingLocate END Point Insert EditingStart Editing Engage Insert EditingEND Insert Editing Press InsertRandom As- semble Editing Access R.A. Edit ScreenPrepare for Editing Load Source CassetteLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditAccess Initial SET Screen Access Main Menu ScreenAccess Jlip ID NO. SET Screen SET Jlip ID NumberTuner Connection ToSystem Connections Simple ConnectionsEN System Connections Connector ScartPerfect Connections Satellite Tuner UnitBasic Connections ConnectorBack of Recorder Mains outlet DecoderSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerConnecting Using a Stereo System Speaker Television Mains outletRear View Tuner Set Access Auto CH SETEN Subsi Diary Sett Ings Auto Channel SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Press %Þ @ #until the item you want to move beginsSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Fine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNEExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET RF Output SystemClock Set Access Initial SETTurn the Recorder on SET Date and TimeStart Clock Operation SET Just ClockNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD PAL-type colour signal and Ccir Provided accessoriesSpeci Fications Ex. Deutschland is selected Ex. Francais is selected for BelgiumInternational Telephone Language Code