JVC HR-S9600EU Colour System Set, Mode, About Ntsc Playback, Appropriate colour system

Page 14

14EN

INFORMATIONONCOLOURSYSTEM

Colour System Set

You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals on this recorder. Follow the procedure below to select the appropriate colour system.

*SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video cassette recorder.

TURN ON THE RECORDER

1– –:– –

2

1 2 3

45 6

78 9

0

1

2MENU

3

4

4

3 OK

1 Press					.
1 Press					.
	ACCESS MAIN MENU
	SCREEN
2 Press MENU.
	ACCESS MODE SET SCREEN
Press %Þ to move the						MAIN MENU
	highlight bar (pointer) to
3 "MODE SET", then press						MODE SET
3 "MODE SET", then press						AUTO CH SET
	OK or #.					MANUAL CH SET
						INITIAL SET
						REC LEVEL CTL
						R.A. EDITT

						[5°] =
						[MENU] : EXIT

	SELECT COLOUR SYSTEM
	MODE

NOTES:

About NTSC Playback

●Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

●The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

●The counter and tape remaining time readings will be incorrect.

●During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

●Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

Press %Þ to move the highlight bar (pointer) to
"COLOUR SYSTEM", then press OK or # to select the
4 appropriate colour system.
	MODE SET				PREVIOUS PAGE
					PREVIOUS PAGE
	B. E. S. T.	ON			POWER SAVE	OFF
	PICTURE CONTROL	AUTO			S-VHS	AUTO
	AUTO TIMER	OFF			AV1 SELECT	VIDEO
	O. S. D.	ON			AV2 SELECT	AV2
	DIRECT REC	ON			COLOUR SYSTEM PAL/NTSC
	AUTO SP=LP TIMER	OFF			TIME SCAN AUDIO	ON
	DIGITAL 3R	ON
	NEXT PAGE
	[5°] =				[5°] =
	[MENU] : EXIT				[MENU] : EXIT

a- PAL/NTSC: To record PAL signals, or play back a PAL or NTSC tape.

b- MESECAM: To record SECAM signals, or play back a MESECAM tape.

RETURN TO NORMAL

SCREEN

5 Press MENU.

Image 14

Contents HR-S9600EU Safety Precautions For Italy Do not place the recorderSituate Recorder Check ContentsBasic Connections Connect Recorder to MainsBack of Recorder Video ConnectionConnect Recorder to TV If you are referring to the front display panel Auto Set UpEN Initial Settings If you are referring to the on-screen displayLanguage Code Preset Download Just Clock If both auto channel set and auto clock set have failedLanguage for the on-screen display Just Clock onLanguage Return to Normal Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays 13 14OK or # Power Save ModeMode SET, then press SAVE, then press OK or #to set to onLI NK TV Auto Power OnLink Functions NexTView LinkAbout Ntsc Playback Colour System SetMode Press %Þ to move the highlight bar pointer toPoint Basic PlaybackLoad a Cassette Start PlaybackActivate HIGH-SPEED Search Playback FeaturesPlayback Manually Adjust TrackingOverride Automatic Tracking Return to AutomaticDigital 3R Digital TBC/NRInstant ReView Activate Instant ReviewRepeat Playback Soundtrack SelectionAudio signal during TimeScan TimeScanMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features Resume Recording Engage RECORD-PAUSE ModeLocate Start Point VHS Super VHS and VHSRecording Level Adjust AudioControl Screen Preparation S.T. Picture SystemEN Recording Or press Record on the recorder RecordingPlayback Timer Programming EN Timer RecordingSatellite Tuner Users Timer WarningÄTIMER indicator Time Express Timer ProgrammingBefore performing Express Timer Programming Return to Normal SET VPS/PDC ModeTimer Mode Engage RECORDER’SCheck, Cancel And Replace Programmes TE+SET, then press OK or # Auto SP→LP TimerFor Example Then press OK or #to selectOK or #to select either Auto TimerAuto TIMER, then press On or OFFBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording RE-SUPPLY Power Remote Control FunctionsSET Remote Control CodeSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVSET Satellite Tuner Brand Code EN Special FeaturesSatellite Tuner Multi-Brand Remote Control Operate Satellite TunerPreparation For Editing Access Mode SETControl SET Mode Select PictureEdit From Camcorder If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder EditingRepeat steps 4 6 as necessary Connector Lanc Cable not provided To Lanc connectorSynchro Editing Recorder PlayerEdit To Or From Another Video Recorder Your recorder NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorder TV Receiver Pin Scart CableAV1 Select Setting AV2 Select SettingStart Dubbing SET Input ModeEngage Audio Dubbing END Audio DubbingInsert Editing Locate END PointEND Insert Editing Engage Insert EditingStart Editing Press InsertPrepare for Editing Access R.A. Edit ScreenRandom As- semble Editing Load Source CassetteStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditAccess Jlip ID NO. SET Screen Access Main Menu ScreenAccess Initial SET Screen SET Jlip ID NumberSystem Connections Connection ToTuner Simple ConnectionsPerfect Connections Connector ScartEN System Connections Satellite Tuner UnitBack of Recorder Mains outlet ConnectorBasic Connections DecoderConnect Decoder Connecting Using a DecoderSelect Input Mode SET TunerRear View Connecting Using a Stereo SystemSpeaker Television Mains outlet EN Subsi Diary Sett Ings Access Auto CH SETTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyChange Station Channel Position When Receiving a Scrambled BroadcastDelete a Channel Press %Þ @ #until the item you want to move beginsChannel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Select Channel to Perform TuningFine-Tuning Channels Already Stored FINE-TUNEVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET RF Output SystemTurn the Recorder on Access Initial SETClock Set SET Date and TimeSET Just Clock Start Clock OperationEnter Receiving Channel Position Number Showview SetupNumber Guide Program Number SetTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and AnswersIndex Front ViewInside View of Front Panel Rear View Remote Control Remote Control LCD Speci Fications PAL-type colour signal and CcirProvided accessories International Telephone Language Code Ex. Deutschland is selectedEx. Francais is selected for Belgium