JVC HR-S9600EU Connecting Using a Stereo System, Speaker Television Mains outlet, Rear View

Page 55

EN55

Connecting/

Using A Stereo

System

FM Tuner

CD Player

Stereo Amplifier

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.

I I I

I

I

I

I

I

I

I

I

I

I

I

I

II

I

I

I
I I	I	II
		II
		I
		I
		II
			I
			I
			I
			I
		I	I

AUX IN or TAPE MONITOR

		Audio Cable
		(not provided)
Speaker	Television	Speaker

Mains outlet

Rear View

SYNCHRO EDIT

JLIP

ANT. IN

AV1 OUT
S OUT	AV1 IN/OUT	L
COMP. Y/C		AUDIO
		OUT
		R

AV2 IN/DECODER

PAUSE/R.A. EDIT

RF OUT

AUDIO OUT

MAKE CONNECTIONS

1 Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system’s receiver or amplifier.

NOTES:

●When connecting your recorder’s audio output connectors to a stereo amplifier, make sure you connect L and R correctly.

●If stereo or bilingual TV broadcasts are receivable in your area, this recorder can record them independently of the TV set and play them back through the connected stereo system.

●When listening to sound through the connected stereo system, turn the TV’s volume down completely.

CAUTIONS:

●This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

●Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Image 55

Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelLanguage Code Preset Download Just Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage 13 14 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenSAVE, then press OK or #to set to on Power Save ModeMode SET, then press OK or #NexTView Link TV Auto Power OnLink Functions LI NKPress %Þ to move the highlight bar pointer to Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointPlayback Playback FeaturesActivate HIGH-SPEED Search Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyDigital TBC/NR Digital 3RSoundtrack Selection Activate Instant ReviewRepeat Playback Instant ReViewTimeScan Audio signal during TimeScanSpeed SP Speed LP Audio output TimeScanMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features VHS Super VHS and VHS Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingControl Screen Adjust AudioRecording Level EN Recording S.T. Picture SystemPreparation Playback RecordingOr press Record on the recorder EN Timer Recording Timer ProgrammingÄTIMER indicator Timer WarningSatellite Tuner Users Before performing Express Timer Programming Express Timer ProgrammingTime Engage RECORDER’S SET VPS/PDC ModeTimer Mode Return to NormalTE+ Check, Cancel And Replace ProgrammesThen press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #On or OFF Auto TimerAuto TIMER, then press OK or #to select eitherAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Code Remote Control FunctionsSET Remote Control RE-SUPPLY PowerOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeOperate Satellite Tuner EN Special FeaturesSatellite Tuner Multi-Brand Remote Control SET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEditing If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderRecorder Player Connector Lanc Cable not provided To Lanc connectorSynchro Editing Repeat steps 4 6 as necessaryEdit To Or From Another Video Recorder Your recorder TV Receiver Pin Scart Cable NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorderAV2 Select Setting AV1 Select SettingEND Audio Dubbing SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Insert EditingPress Insert Engage Insert EditingStart Editing END Insert EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditSET Jlip ID Number Access Main Menu ScreenAccess Initial SET Screen Access Jlip ID NO. SET ScreenSimple Connections Connection ToTuner System ConnectionsSatellite Tuner Unit Connector ScartEN System Connections Perfect ConnectionsDecoder ConnectorBasic Connections Back of Recorder Mains outletSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderSpeaker Television Mains outlet Connecting Using a Stereo SystemRear View Auto Channel Set Access Auto CH SETTuner Set EN Subsi Diary Sett IngsView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetSET Date and Time Access Initial SETClock Set Turn the Recorder onStart Clock Operation SET Just ClockGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD Provided accessories PAL-type colour signal and CcirSpeci Fications Ex. Francais is selected for Belgium Ex. Deutschland is selectedInternational Telephone Language Code