JVC HR-S9600EU specifications Preset Download

Page 8
Set the Video Channel to off manually. (☞ pg. 63)
2
[MENU] : EXIT
SET VIDEO CHANNEL
GUIDE PROG SET
PLEASE WAIT
[MENU] : EXIT
T-V LINK
PLEASE WAIT
● If "– –:––" appears on the display panel, refer to page 9.
● If you are using the on- screen display, the T-V LINK screen will appear. Then the GUIDE PROG SET screen will appear during Guide Program number set.
● If you press any button on the recorder or remote control while downloading is in progress, it will be interrupted.
[5°] = [MENU] : EXIT
Preset position on the display panel increases from "CH1"; do NOT press any button on the recorder or remote control until the display panel shows either the display as illustrated on page 9 or "– –:––".
AUTO SET T-V LINK
Press %Þ to move the highlight bar (pointer) to "T-V LINK" and press OK or #.
If you are referring to the on-screen display
Press %Þ
to select "CH – –" and press OK or #.
Press OK.
If you are referring to the front display panel
1
INITIAL SETTINGS (cont.)
When you connect the recorder and your TV via fully-wired
21-pin SCART cable (☞ pg. 4), you can set the recorder's tuner channels by downloading preset data from your TV instead of using the Auto Set Up function (☞ pg. 6). After downloading is completed, the recorder sets the clock and Guide Program number automatically. For details, refer to the instruction manual for your TV.
Perform steps 1 to 3 of "Auto Set Up" on page 6 and 7 before continuing.
PERFORM PRESET DOWNLOAD

8EN

Preset

Download

You can use this function only with the TV offering

T-V Link, etc.*

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NEXTVIEWLINK via fully- wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

1– –:– –

2

1 2 3

45 6

78 9

0

1

2MENU

3

4

4

3 OK

￿

NOTES:

●In the area where no TV station transmits a PDC signal, the recorder can perform neither auto clock set nor auto Guide Program number set.

●If there is a power cut, or if you press or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto clock may not function properly depending on the reception condition.

●When you perform T-V LINK function, be sure to use fully- wired 21-pin SCART cable.

●On this recorder, the characters available for station’s name

(ID) are A–Z, 0–9, –, *, + and (space). Some downloaded station’s name may differ from those of your TV (☞ pg. 60).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents HR-S9600EU Safety Precautions For Italy Do not place the recorderCheck Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsBack of Recorder Video ConnectionConnect Recorder to TV Auto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Preset Download If both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage ENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysReturn to Normal Screen 13 14Power Save Mode Mode SET, then pressOK or # SAVE, then press OK or #to set to onTV Auto Power On Link FunctionsLI NK NexTView LinkColour System Set ModeAbout Ntsc Playback Press %Þ to move the highlight bar pointer toBasic Playback Load a CassettePoint Start PlaybackActivate HIGH-SPEED Search Playback FeaturesPlayback Adjust Tracking Override Automatic TrackingManually Return to AutomaticDigital 3R Digital TBC/NRActivate Instant Review Repeat PlaybackInstant ReView Soundtrack SelectionAudio signal during TimeScan TimeScanMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features Engage RECORD-PAUSE Mode Locate Start PointResume Recording VHS Super VHS and VHSRecording Level Adjust AudioControl Screen Preparation S.T. Picture SystemEN Recording Or press Record on the recorder RecordingPlayback Timer Programming EN Timer RecordingSatellite Tuner Users Timer WarningÄTIMER indicator Time Express Timer ProgrammingBefore performing Express Timer Programming SET VPS/PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes TE+Auto SP→LP Timer For ExampleSET, then press OK or # Then press OK or #to selectAuto Timer Auto TIMER, then pressOK or #to select either On or OFFBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording Remote Control Functions SET Remote ControlRE-SUPPLY Power CodeTV Multi-brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVEN Special Features Satellite Tuner Multi-Brand Remote ControlSET Satellite Tuner Brand Code Operate Satellite TunerAccess Mode SET Control SET ModePreparation For Editing Select PictureIf the camcorder has no S-VIDEO output connector Recorder If the camcorder has an S-VIDEO output connector RecorderEdit From Camcorder EditingConnector Lanc Cable not provided To Lanc connector Synchro EditingRepeat steps 4 6 as necessary Recorder PlayerEdit To Or From Another Video Recorder NEL or Or AV Provided AV mode Mode Another recorder TV ReceiverYour recorder Your recorder TV Receiver Pin Scart CableAV1 Select Setting AV2 Select SettingSET Input Mode Engage Audio DubbingStart Dubbing END Audio DubbingInsert Editing Locate END PointEngage Insert Editing Start EditingEND Insert Editing Press InsertAccess R.A. Edit Screen Random As- semble EditingPrepare for Editing Load Source CassetteLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A. Edit END R.A. EditAccess Main Menu Screen Access Initial SET ScreenAccess Jlip ID NO. SET Screen SET Jlip ID NumberConnection To TunerSystem Connections Simple ConnectionsConnector Scart EN System ConnectionsPerfect Connections Satellite Tuner UnitConnector Basic ConnectionsBack of Recorder Mains outlet DecoderConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerRear View Connecting Using a Stereo SystemSpeaker Television Mains outlet Access Auto CH SET Tuner SetEN Subsi Diary Sett Ings Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move beginsAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List Perform Tuning Fine-Tuning Channels Already StoredSelect Channel to FINE-TUNEAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output SystemAccess Initial SET Clock SetTurn the Recorder on SET Date and TimeSET Just Clock Start Clock OperationShowview Setup NumberEnter Receiving Channel Position Number Guide Program Number SetTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and AnswersIndex Front ViewInside View of Front Panel Rear View Remote Control Remote Control LCD Speci Fications PAL-type colour signal and CcirProvided accessories International Telephone Language Code Ex. Deutschland is selectedEx. Francais is selected for Belgium
Top Page Image Contents