JVC HR-S9600EU specifications SET VPS/PDC Mode, Return to Normal, Engage RECORDER’S, Timer Mode

Page 31

6

ENTER CHANNEL POSITION

Press TV PROG +/–.

– P1 –

 

START

STOP

21:00

= 22:00

 

SP

VPS/PDC OFF

 

DATE

TV PROG

 

25.12

1

 

[+/–] =

ARD

 

 

 

[PROG] : EXIT

 

 

SP

 

 

SET TAPE SPEED

7 Press SP/LP ( ) to set the tape speed.

8

SET VPS/PDC MODE

Press VPS/PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, VPS/PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/PDC"

 

is not lit on the display panel, VPS/PDC is set to OFF.

 

☞ "VPS/PDC Recording" in the right column.

 

RETURN TO NORMAL

 

SCREEN

 

After confirming all information is correct, press PROG

 

or OK. "PROGRAM COMPLETED" appears on the

9 screen for about 5 seconds, then normal screen

 

appears.

 

● Repeat steps 1 – 9 for each additional programme.

 

ENGAGE RECORDER’S

10

TIMER MODE

Press ä (or äTIMER). The recorder turns off automati-

 

 

cally and ä appears on the display panel. The äTIMER

 

indicator on the recorder also lights up.

 

● To disengage the timer, press ä (or äTIMER) again.

EN31

Satellite Tuner Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Set "AV2 SELECT" to "AV2" (☞ pg. 44).

2 Perform steps 1 – 10. Enter "L-2" for the channel position in step 6.

3 Set the satellite tuner to the appropriate channel before the selected programme begins.

4 Leave the satellite tuner's power on.

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.

NOTES:

● When you use Express Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● VPS/PDC recording is also possible when a satellite tuner or a cable system is connected to AV2 IN/DECODER on your recorder.

● VPS/PDC recording is also possible via the AV1 IN/OUT connector.

How to check if the station being received transmits a VPS/PDC signal

1 Press – –:– – until the channel position appears on the display panel.

2 Hold down START+ for about 5 seconds.

● "VPS/PDC" appears blinking on the display panel. If a VPS/PDC signal is detected from the station, "VPS/ PDC" will stop blinking.

If no VPS/PDC signal is detected from the station, "VPS/

PDC" will blink at a slower rate.

3 Press – –:– – or START+ again to return to normal display.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the recording is to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (☞ pg. 32).

NOTES:

●The warning only appears if

you’re not in the Timer mode at that time.

●If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

Page 30 Page 32
Image 31
Page 30 Page 32
Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelLanguage Code Preset Download Just Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage 13 14 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenSAVE, then press OK or #to set to on Power Save ModeMode SET, then press OK or #NexTView Link TV Auto Power OnLink Functions LI NKPress %Þ to move the highlight bar pointer to Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointPlayback Playback FeaturesActivate HIGH-SPEED Search Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyDigital TBC/NR Digital 3RSoundtrack Selection Activate Instant ReviewRepeat Playback Instant ReViewTimeScan Audio signal during TimeScanSpeed SP Speed LP Audio output TimeScanMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features VHS Super VHS and VHS Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingControl Screen Adjust AudioRecording Level EN Recording S.T. Picture SystemPreparation Playback RecordingOr press Record on the recorder EN Timer Recording Timer ProgrammingÄTIMER indicator Timer WarningSatellite Tuner Users Before performing Express Timer Programming Express Timer ProgrammingTime Engage RECORDER’S SET VPS/PDC ModeTimer Mode Return to NormalTE+ Check, Cancel And Replace ProgrammesThen press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #On or OFF Auto TimerAuto TIMER, then press OK or #to select eitherAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Code Remote Control FunctionsSET Remote Control RE-SUPPLY PowerOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeOperate Satellite Tuner EN Special FeaturesSatellite Tuner Multi-Brand Remote Control SET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEditing If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderRecorder Player Connector Lanc Cable not provided To Lanc connectorSynchro Editing Repeat steps 4 6 as necessaryEdit To Or From Another Video Recorder Your recorder TV Receiver Pin Scart Cable NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorderAV2 Select Setting AV1 Select SettingEND Audio Dubbing SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Insert EditingPress Insert Engage Insert EditingStart Editing END Insert EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditSET Jlip ID Number Access Main Menu ScreenAccess Initial SET Screen Access Jlip ID NO. SET ScreenSimple Connections Connection ToTuner System ConnectionsSatellite Tuner Unit Connector ScartEN System Connections Perfect ConnectionsDecoder ConnectorBasic Connections Back of Recorder Mains outletSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderSpeaker Television Mains outlet Connecting Using a Stereo SystemRear View Auto Channel Set Access Auto CH SETTuner Set EN Subsi Diary Sett IngsView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetSET Date and Time Access Initial SETClock Set Turn the Recorder onStart Clock Operation SET Just ClockGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD Provided accessories PAL-type colour signal and CcirSpeci Fications Ex. Francais is selected for Belgium Ex. Deutschland is selectedInternational Telephone Language Code
Top Page Image Contents