JVC HR-S9600EU specifications Recording Features

Page 23

Recording Features

C.RESET/CANCEL

EN23

Record One Programme

While Watching Another

If your recorder is connected to the TV via AV connection, . . .

. . . press TV/VCR. The recorder's VCR indicator and the TV broadcast being recorded disappear.

SELECT CHANNEL TO

WATCH

1 Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.

●The programme selected with the TV’s channel controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.

●If a decoder is connected to the recorder (☞ pg. 54), you can select a scrambled channel as well with the TV channel controls.

1– –:– –

––:– –

2

1 2 3

45 6

78 9

0000	0
0000
	1
	2

TV/VCR

3

4

4

3

TV PROG

Elapsed Recording Time Indication

You can check the exact time of a recording.

SET COUNTER DISPLAY

1 Press – –:– – (or DISPLAY) until a counter reading appears on the display panel.

RESET COUNTER

2 Press 0000 (or C.RESET/CANCEL) before starting recording or playback.

●The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs.

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

2 Press RECORD again. "" blinks and 0:30 appears on the front display panel.

SET RECORDING DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press – –:– – (or DISPLAY) until the time remaining on the tape appears.

●The display panel shows the tape remaining time with "" displayed.

●By pressing the – –:– – (or DISPLAY) button, you can change the display to show the counter reading, channel position*, clock time or tape remaining time.

*channel position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 23

Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderBack of Recorder Video ConnectionConnect Recorder to TV If you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelLanguage Code Preset Download Just Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage 13 14 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenSAVE, then press OK or #to set to on Power Save ModeMode SET, then press OK or #NexTView Link TV Auto Power OnLink Functions LI NKPress %Þ to move the highlight bar pointer to Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Playback FeaturesPlayback Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyDigital TBC/NR Digital 3RSoundtrack Selection Activate Instant ReviewRepeat Playback Instant ReViewTimeScan Audio signal during TimeScanMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features VHS Super VHS and VHS Engage RECORD-PAUSE ModeLocate Start Point Resume RecordingRecording Level Adjust AudioControl Screen Preparation S.T. Picture SystemEN Recording Or press Record on the recorder RecordingPlayback EN Timer Recording Timer ProgrammingSatellite Tuner Users Timer WarningÄTIMER indicator Time Express Timer ProgrammingBefore performing Express Timer Programming Engage RECORDER’S SET VPS/PDC ModeTimer Mode Return to NormalTE+ Check, Cancel And Replace ProgrammesThen press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #On or OFF Auto TimerAuto TIMER, then press OK or #to select eitherBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording Code Remote Control FunctionsSET Remote Control RE-SUPPLY PowerOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeOperate Satellite Tuner EN Special FeaturesSatellite Tuner Multi-Brand Remote Control SET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEditing If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderRecorder Player Connector Lanc Cable not provided To Lanc connectorSynchro Editing Repeat steps 4 6 as necessaryEdit To Or From Another Video Recorder Your recorder TV Receiver Pin Scart Cable NEL or Or AV Provided AV mode Mode Another recorderTV Receiver Your recorderAV2 Select Setting AV1 Select SettingEND Audio Dubbing SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Insert EditingPress Insert Engage Insert EditingStart Editing END Insert EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditSET Jlip ID Number Access Main Menu ScreenAccess Initial SET Screen Access Jlip ID NO. SET ScreenSimple Connections Connection ToTuner System ConnectionsSatellite Tuner Unit Connector ScartEN System Connections Perfect ConnectionsDecoder ConnectorBasic Connections Back of Recorder Mains outletSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderRear View Connecting Using a Stereo SystemSpeaker Television Mains outlet Auto Channel Set Access Auto CH SETTuner Set EN Subsi Diary Sett IngsView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetSET Date and Time Access Initial SETClock Set Turn the Recorder onStart Clock Operation SET Just ClockGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD Speci Fications PAL-type colour signal and CcirProvided accessories International Telephone Language Code Ex. Deutschland is selectedEx. Francais is selected for Belgium