JVC HR-S9600EU specifications Auto SP→LP Timer, For Example, SET, then press OK or #

Page 33

1– –:– –

2

1 2 3

45 6

78 9

0

1

2MENU

3

4

4

3

EN33

Auto SP→LP Timer

If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording.

For Example . . .

Recording a programme of 210 minutes in length onto a 180- minute tape

Approximately 150 minutes	Approximately 60 minutes

SP mode	LP mode

Total 210 minutes

Make sure you set "AUTO SP→LP TIMER" to "ON" at the Mode

Set screen before the timer-recording starts.

	1		ACCESS MAIN MENU SCREEN
	1	Press MENU.
		Press MENU.
OK

	2		ACCESS MODE SET SCREEN
		Press %Þ to move the highlight bar (pointer) to "MODE
			SET", then press OK or #.
	3		SELECT MODE
		Press %Þ to move the		MODE SET
			highlight bar (pointer) to	B. E. S. T.	ON
			"AUTO SP→LP TIMER",	B. E. S. T.	ON
			"AUTO SP→LP TIMER",	PICTURE CONTROL	AUTO
			then press OK or #to select	AUTO TIMER	OFF
			"ON".	O. S. D.	ON
			"ON".	DIRECT REC	ON
				AUTO SP=LP TIMER	ON
				DIGITAL 3R	ON
				NEXT PAGE
				[5°] =
				[MENU] : EXIT

	4		RETURN TO NORMAL SCREEN
	4	Press MENU.

NOTES:

●If you have programmed the recorder to timer-record 2 or

more programmes, the second programme and those thereafter may not fit on the tape if you set "AUTO SP→LP TIMER" to "ON". In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.

●In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.

●There may be some noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode.

●The Auto SP→LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths.

●If you perform timer recording with both VPS/PDC and the Auto SP→LP Timer activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety.

Image 33

Contents HR-S9600EU Safety Precautions Do not place the recorder For ItalyBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsVideo Connection Connect Recorder to TVBack of Recorder EN Initial Settings Auto Set UpIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Preset Download Language for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage On-Screen Displays ENABLE/DISABLE ON-SCREEN DisplayReturn to Normal Screen 13 14Mode SET, then press Power Save ModeOK or # SAVE, then press OK or #to set to onLink Functions TV Auto Power OnLI NK NexTView LinkMode Colour System SetAbout Ntsc Playback Press %Þ to move the highlight bar pointer toLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Features PlaybackActivate HIGH-SPEED Search Override Automatic Tracking Adjust TrackingManually Return to AutomaticDigital TBC/NR Digital 3RRepeat Playback Activate Instant ReviewInstant ReView Soundtrack SelectionTimeScan Audio signal during TimeScanTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Basic Recording Recording Features Locate Start Point Engage RECORD-PAUSE ModeResume Recording VHS Super VHS and VHSAdjust Audio Control ScreenRecording Level S.T. Picture System EN RecordingPreparation Recording PlaybackOr press Record on the recorder EN Timer Recording Timer ProgrammingTimer Warning ÄTIMER indicatorSatellite Tuner Users Express Timer Programming Before performing Express Timer ProgrammingTime Timer Mode SET VPS/PDC ModeReturn to Normal Engage RECORDER’STE+ Check, Cancel And Replace ProgrammesFor Example Auto SP→LP TimerSET, then press OK or # Then press OK or #to selectAuto TIMER, then press Auto TimerOK or #to select either On or OFFProg REC Mode Automatic Satellite Programme RecordingBefore performing the following steps SET Remote Control Remote Control FunctionsRE-SUPPLY Power CodeControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSatellite Tuner Multi-Brand Remote Control EN Special FeaturesSET Satellite Tuner Brand Code Operate Satellite TunerControl SET Mode Access Mode SETPreparation For Editing Select PictureIf the camcorder has an S-VIDEO output connector Recorder If the camcorder has no S-VIDEO output connector RecorderEdit From Camcorder EditingSynchro Editing Connector Lanc Cable not provided To Lanc connectorRepeat steps 4 6 as necessary Recorder PlayerEdit To Or From Another Video Recorder TV Receiver NEL or Or AV Provided AV mode Mode Another recorderYour recorder Your recorder TV Receiver Pin Scart CableAV2 Select Setting AV1 Select SettingEngage Audio Dubbing SET Input ModeStart Dubbing END Audio DubbingLocate END Point Insert EditingStart Editing Engage Insert EditingEND Insert Editing Press InsertRandom As- semble Editing Access R.A. Edit ScreenPrepare for Editing Load Source CassetteLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditAccess Initial SET Screen Access Main Menu ScreenAccess Jlip ID NO. SET Screen SET Jlip ID NumberTuner Connection ToSystem Connections Simple ConnectionsEN System Connections Connector ScartPerfect Connections Satellite Tuner UnitBasic Connections ConnectorBack of Recorder Mains outlet DecoderSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerConnecting Using a Stereo System Speaker Television Mains outletRear View Tuner Set Access Auto CH SETEN Subsi Diary Sett Ings Auto Channel SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Press %Þ @ #until the item you want to move beginsSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Fine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNEExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET RF Output SystemClock Set Access Initial SETTurn the Recorder on SET Date and TimeStart Clock Operation SET Just ClockNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers Ä remain lit on the display panel. Is there Problem?Front View IndexInside View of Front Panel Rear View Remote Control Remote Control LCD PAL-type colour signal and Ccir Provided accessoriesSpeci Fications Ex. Deutschland is selected Ex. Francais is selected for BelgiumInternational Telephone Language Code