JVC HR-S9500EK setup guide Load a Cassette, Point, Start Playback, Stop Playback

Page 10

10

BASICOPERATIONS

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

4	STOP/EJECT	3
	STOP/EJECT	PLAY
		1

PAUSE

TV	PROG	2	REW	FF	2
TV		2	REW	FF	2
	3				TV PROG
	3
	LAY
	1				FF 2
2 REW					FF 2
2 REW					PAUSE
4	STOP				PAUSE
4	STOP

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

	1		LOAD A CASSETTE
			Make sure the window side is up, the rear label side is
			facing you and the arrow on the front of the cassette is
			point toward the recorder. Don’t apply too much
			pressure when inserting.

			● The recorder power comes on automatically and the
			counter is reset to 0:00:00.
			● If the record safety tab has been removed, playback
			begins automatically.

			FIND PROGRAMME START
	2		POINT
			If the tape is advanced past the start point, press REW.
			To go forward, press FF.
	3		START PLAYBACK
			Press PLAY. "BEST" appears blinking in the recorder's
			display panel during automatic tracking (☞ pg. 20)
			● Playback picture quality of LP recordings will not be
			● Playback picture quality of LP recordings will not be
			as high as SP recordings.

	4		STOP PLAYBACK
			Press STOP on the remote or STOP/EJECT on the
			recorder’s front panel. Then press STOP/EJECT to
			remove the cassette.

3

JOG/SHUTTLE

Usable cassettes

SHUTTLE

JOG

Tape Position Indicator

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end)

shows you where you are on 0 + the tape.

”O.S.D.” (☞ pg. 42) must

be set to “ON”, or the

indicator will not appear. Beginning

3

+ +

1:23:45 REMAIN 2:35

End

●Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

●This video recorder can record on regular VHS and Super VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes, both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes.

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Image 10

Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletMains outlet Mains Power Cord Back of TV Audio in connectorsBack of Recorder Will appear Beginning Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayPress Prog Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Correct numberTimer Warning PDC RecordingStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Or press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackReturn to Normal Screen Access Main MenuAdjust Audio Activate SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTEngage Auto Satellite Prog REC Mode Access Mode SET ScreenSelect AV2 Select Mode Before performing the following stepsRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverMinimizing Picture Degradation While Editing Editing Mode SettingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder Your recorder AV2 Select SettingTV Receiver Quality S-VHS picturesLoad Source Cassette Access R.A. Edit ScreenPrepare for Editing Start Source PlaybackStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditInsert Editing SET Input ModeReset the Counter Locate END PointStart Editing Engage Insert EditingEND Insert Editing END Audio Dubbing Engage Audio DubbingStart Dubbing Audio OUTInformation On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen SET Jlip ID NumberENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsAuto SP→LP Timer Auto TimerRetake Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set After Scan Completed Screen preset positionsProcedures Is displayed on the screenInformation Storing Channels ManuallyEnter NEW Channel Close Confirmation ScreenFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?No power is applied to the recorder TroubleshootingConnect the mains power cord Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical