JVC HR-S9500EK setup guide Access Mode SET Screen, Select AV2 Select Mode

Page 29

REC LINK

29

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder's AV2 IN connector. (☞ pg. 28)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 IN connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 16) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

1

2

3

4

5

ACCESS MAIN MENU SCREEN

Press MENU.

ACCESS MODE SET SCREEN

Move the highlight bar (pointer) to "MODE SET" by pressing %Þ, then press OK or %.

SELECT AV2 SELECT MODE

Move the highlight bar (pointer) to "AV2 SELECT", by pressing %Þ, then press OK or %to set to "SAT".

MODE SET

 

 

 

PREVIOUS PAGE

 

 

 

 

 

 

 

 

AUTO TIMER

OFF

 

 

AV2 SELECT

SAT

 

O. S. D.

ON

 

 

TIME SCAN AUDIO

ON

 

B. E. S. T.

ON

 

 

 

 

AUTO SP=LP TIMER

OFF

 

 

 

 

DIGITAL 3R

ON

 

 

 

 

S-VHS

AUTO

 

 

 

 

EDIT

OFF

 

 

 

 

NEXT PAGE

 

 

 

 

 

 

[5°] =

 

 

 

[5°] =

 

 

[MENU] : EXIT

 

 

 

[MENU] : EXIT

 

 

SET TAPE SPEED

Press SP/LP () to set the tape speed.

ENGAGE AUTO SATELLITE PROG REC MODE

Press and hold REC LINK for about 2 seconds. The button lights up and the recorder turns off automatically.

●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

●Auto Satellite Prog recording is possible with the AV2 IN connector only.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (☞ pg. 23).

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The REC LINK button blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 20) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 55) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN connector.

Page 28 Page 30
Image 29
Page 28 Page 30
Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart AV1 OUT switchBack of TV Mains outletBack of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayBefore performing Video Plus+ Timer Programming Video Plus+ Timer ProgrammingPress Prog Correct numberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Playback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Switch SignalSatellite Receiver Unit Rear panel AV1 OUTSelect AV2 Select Mode Access Mode SET ScreenEngage Auto Satellite Prog REC Mode Before performing the following stepsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder TV Receiver AV2 Select SettingYour recorder Quality S-VHS picturesPrepare for Editing Access R.A. Edit ScreenLoad Source Cassette Start Source PlaybackLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Engage Insert EditingStart Editing Start Dubbing Engage Audio DubbingEND Audio Dubbing Audio OUTAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal SET Jlip ID NumberAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerNtsc Playback Repeat PlaybackRetake Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenEnter NEW Channel Storing Channels ManuallyInformation Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersConnect the mains power cord TroubleshootingNo power is applied to the recorder Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x
Top Page Image Contents