JVC HR-S9500EK Automatic Satellite Programme Recording, Satellite Receiver Unit, Switch Signal

Page 28

28ADVANCEDOPERATIONS (cont.)

Automatic Satellite Programme Recording

This facility allows you to record automatically a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder's AV2 IN connector and programme the timer on the satellite receiver; the recorder starts recording when the signals input from the satellite receiver to the AV2 IN connector, and when there is no input signals the recorder stops recording and the power shuts off.

Outdoor Unit

Satellite Cable

Satellite Receiver Unit

DECODER

VCR

TV

	Aerial	Aerial connector
	Aerial	Back of TV
		Back of TV

21-pin AV input connector (SCART)

TV Aerial cable

ANT. IN

EXT.2EXT.1

RF OUT

Mains outlet

AV1 OUT

S OUT

COMP. Y/C

Back of Recorder

AV1 OUT switch

		ANT. IN
AV1 IN/OUT	R	L
	AUDIO OUT
		JLIP
		RF OUT
AV2 IN
		PAUSE/
		R.A. EDIT

IMPORTANT

Set "AV2 SELECT" to "SAT" on the Mode Set screen in step 3 of page 29.

If you set "AV2 SELECT" to "SAT"...

●It is possible to view a satellite programme with the TV set to its AV mode even if the recorder's power is turned off.

●The AV2 IN connector's input is the same signal that is controlled by the rear panel AV1 OUT switch as shown below:

a- If both the satellite receiver and the TV are compatible with the Y/C signal, set the AV1 OUT switch to Y/C in order to take advantage of high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

b- If the satellite receiver and/or the TV are/is not compatible with the Y/C signal, set the AV1 OUT switch to COMP.

	AV2 SELECT setting on	Rear panel AV1 OUT	AV2 IN connector input
	the MODE SET screen	switch	signal

	SAT	COMP.	Composite signal*

		Y/C	Y/C signal**
		Y/C	Y/C signal**

*The composite signal is a regular video signal.

**The Y/C signal is a signal in which the luminance and chrominance signals are separated.

NOTE:

Refer to the instructions supplied with your satellite receiver.

Image 28

Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide AV1 OUT switch To connect to a TV with 21-pin AV input connector ScartBack of TV Mains outletMains outlet Mains Power Cord Back of TV Audio in connectorsBack of Recorder Will appear Beginning Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Before performing Video Plus+ Timer ProgrammingPress Prog Correct numberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingStart Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Recording PlaybackOr press Record on the recorder During B.E.S.TPlayback Picture Adjustment Manual TrackingDigital TBC/NR Digital 3RLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchAudio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan TimeScan AudioSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAccess Main Menu Adjust AudioReturn to Normal Screen Activate SpatializerSwitch Signal Automatic Satellite Programme RecordingSatellite Receiver Unit Rear panel AV1 OUTAccess Mode SET Screen Select AV2 Select ModeEngage Auto Satellite Prog REC Mode Before performing the following stepsTV Multi-brand Remote Control Control Your TV Using Additional ButtonsRemote Con- trol Functions SET TV Brand CodeSET Remote Control Code RE-SUPPLY PowerSET Satellite Receiver Brand Code Operate Satellite ReceiverMinimizing Picture Degradation While Editing Editing Mode SettingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder AV2 Select Setting TV ReceiverYour recorder Quality S-VHS picturesAccess R.A. Edit Screen Prepare for EditingLoad Source Cassette Start Source PlaybackLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A. Edit END R.A. EditSET Input Mode Reset the CounterInsert Editing Locate END PointStart Editing Engage Insert EditingEND Insert Editing Engage Audio Dubbing Start DubbingEND Audio Dubbing Audio OUTTerminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenInformation On J Terminal SET Jlip ID NumberAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Auto TimerRepeat Playback Ntsc PlaybackRetake Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Enter NEW ChannelInformation Close Confirmation ScreenFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Access Manual Channel SET Screen Select NEW StationClose Confirmation Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?No power is applied to the recorder TroubleshootingConnect the mains power cord Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical