JVC HR-S9500EK setup guide Connection To Stereo System, Audio Cable not provided Speaker

Page 45

SYSTEMCONNECTIONS

45

Connection To

AStereo System

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.

FM Tuner

CD Player

Stereo Amplifier

I

I

I

I

I

I

I

I

I

I

I

I I I

 

 

I I

I

II

 

 

I

 

 

II

 

 

II

 

 

II

AUX IN or TAPE MONITOR

Speaker

Television

Audio Cable (not provided)

Speaker

ANT. IN

 

AV1 OUT

 

S OUT

AV1 IN/OUT

R L

 

COMP. Y/C

AUDIO OUT

 

 

 

 

JLIP

 

 

RF OUT

 

AV2 IN

 

 

 

PAUSE/

Mains outlet

 

R.A. EDIT

 

 

Back of Recorder

 

AUDIO OUT

MAKE CONNECTIONS

1 Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system's receiver or amplifier.

NOTES:

When connecting your recorder's audio output connectors to a stereo amplifier, make sure you connect L and R correctly.

If you can receive NICAM TV broadcasts in your area, this recorder can record them independently of the TV set and play them back through the connected stereo system.

When listening to sound through the connected stereo system, turn the TV's volume down completely.

CAUTIONS:

This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Image 45
Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart AV1 OUT switchBack of TV Mains outletBack of TV Audio in connectors Mains outlet Mains Power CordBack of Recorder Before performing the following procedure, make sure that Will appear BeginningGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayBefore performing Video Plus+ Timer Programming Video Plus+ Timer ProgrammingPress Prog Correct numberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypePlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Playback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Switch SignalSatellite Receiver Unit Rear panel AV1 OUTSelect AV2 Select Mode Access Mode SET ScreenEngage Auto Satellite Prog REC Mode Before performing the following stepsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverEditing Mode Setting Minimizing Picture Degradation While EditingAdvantages Of S-VHS Video Recorders Edit From Camcorder Edit To Or From Another Video Recorder TV Receiver AV2 Select SettingYour recorder Quality S-VHS picturesPrepare for Editing Access R.A. Edit ScreenLoad Source Cassette Start Source PlaybackLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditReset the Counter SET Input ModeInsert Editing Locate END PointEngage Insert Editing Start EditingEND Insert Editing Start Dubbing Engage Audio DubbingEND Audio Dubbing Audio OUTAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal SET Jlip ID NumberAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerNtsc Playback Repeat PlaybackRetake Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenEnter NEW Channel Storing Channels ManuallyInformation Close Confirmation ScreenChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting No power is applied to the recorderConnect the mains power cord Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x