JVC HR-S9500EK setup guide Storing Channels Manually, Enter NEW Channel, Information

Page 50

06 CH21 –––– +/–

50

SUBSIDIARYSETTINGS(cont.)

Storing Channels Manually

	1	2	3
			2
NUMBER	4	5	6
NUMBER
	7	8	9
		0	4
	1

OK

MENU

ATTENTION

After you have stored channels manually, be sure to perform Guide Program Number Set (☞ pg. 56) in order to get proper results from Video Plus+ timer recording.

To store channels that were not stored during Auto Set Up (☞ pg. 8) or Auto Channel Set (☞ pg. 48).

	ACCESS MAIN MENU
1 Press MENU.
	ACCESS CONFIRMATION
	SCREEN
	Press %Þto move the highlight bar (pointer) to
	“MANUAL CH SET”, then press OK or%. The Confir-
2 mation screen appears.
	SELECT POSITION
	Press %Þ%%until an		(Ex.) To store in position 6.
	open position in which				PR	CH	ID	PR CH		ID
	you want to store a				PR	CH	ID	PR CH		ID
	you want to store a	01				26	BBC1	08		– – – –
3 channel begins blinking,		02				33	BBC2	09		– – – –
	then press OK. The	03				23	ITV	10		– – – –
	then press OK. The	04				30	CH4	11		– – – –
	Manual Channel Set	05				37	CH5	12		– – – –
	screen appears.			06			– – – –	13		– – – –
	screen appears.	07					– – – –	14		– – – –
		07					– – – –	14		– – – –
					[5°55]
					=	: EDIT
					= [X] : DELETE
					[MENU] : EXIT
		The blueback screen and the
		programme currently being
		broadcast by the selected channel
		appear alternately for 8 seconds
		each.

	INPUT CHANNEL
	Press the NUMBER keys to
	input the channel number
4 you want to store.					PR	CH	ID	FINE

●To input the registered station name (ID – ☞

	pg. 53), press%until "– –	[0–9] : SELECT
	pg. 53), press%until "– –	[°°] : CURSOR +=
	–Ê –" (ID setting) begins	: OK
	blinking, then press %Þ.	: OK
	blinking, then press %Þ.	[MENU] : EXIT

	● For fine tuning	%	The blueback screen and the
	adjustment, press
			programme currently being
	until "+/–" begins
			broadcast by the selected channel
	blinking, then press		appear alternately for 8 seconds
	%Þ.		each.
	While tuning, “+” or “–” appears.

		ENTER NEW CHANNEL
	5	INFORMATION
	5	Press OK and the Confirmation screen appears.
		Press OK and the Confirmation screen appears.

		● Repeat steps 3 through 5 as necessary.

6	CLOSE CONFIRMATION SCREEN
	Press MENU.

	● To change positions, see "Change Station Preset
	Position" (☞ pg. 51).
	● If you wish to set station names other than the ones
	registered in your recorder, ☞ "Set Stations (B)" on
	page 52.

Image 50

Contents HR-S9500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletBack of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPlayback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayPress Prog Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Correct numberTimer Warning PDC RecordingStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackReturn to Normal Screen Access Main MenuAdjust Audio Activate SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTEngage Auto Satellite Prog REC Mode Access Mode SET ScreenSelect AV2 Select Mode Before performing the following stepsRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder Your recorder AV2 Select SettingTV Receiver Quality S-VHS picturesLoad Source Cassette Access R.A. Edit ScreenPrepare for Editing Start Source PlaybackStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditInsert Editing SET Input ModeReset the Counter Locate END PointEND Insert Editing Engage Insert EditingStart Editing END Audio Dubbing Engage Audio DubbingStart Dubbing Audio OUTInformation On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen SET Jlip ID NumberENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsAuto SP→LP Timer Auto TimerRetake Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsProcedures Is displayed on the screenInformation Storing Channels ManuallyEnter NEW Channel Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Connect the mains power cord TroubleshootingNo power is applied to the recorder Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexAudio OUT L/R Connectors enable Rear ViewRemote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical