JVC HR-S9500EK setup guide SET PDC Mode, Return to Normal, Screen, Engage RECORDER’S, Timer Mode

Page 17

ENTER PRESET POSITION

 

Press TV PROG +/– to

 

– P1 –

 

enter the preset position

 

 

 

 

6 corresponding to the

START

STOP

21:00

= 22:00

 

broadcasting station you

SP

VPS/PDC OFF

 

wish to record.

 

 

 

 

DATE

TV PROG

 

 

 

25.12

1

 

 

 

[+/–] =

BBC 1

 

 

 

 

 

 

 

[PROG] : EXIT

 

 

 

 

SP

 

 

SET TAPE SPEED

 

7 Press SP/LP (

) to set the tape speed.

 

8

SET PDC MODE

 

Press PDC to select "ON" or "OFF".

 

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

☞"PDC Recording" in the right column.

● VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

RETURN TO NORMAL

SCREEN

After confirming all information is correct, press PROG

or OK. "PROGRAM COMPLETED" appears on the

9 screen for about 5 seconds, then normal screen

appears.

● Repeat steps 1 – 9 for each additional programme.

ENGAGE RECORDER’S

17

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Set "AV2 SELECT" to the appropriate mode. ☞ pg. 35 2 Perform steps 1 – 10. Enter "L-2" for the preset position

in step 6.

3 Set the satellite receiver to the appropriate channel before the selected programme begins.

4 Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel.

(☞ step 8 in the left column).

NOTES:

● Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder.

● PDC recording is also possible via the AV1 IN/OUT connector.

10

TIMER MODE

Press ä(TIMER). The recorder turns off automatically

and äappears on the display panel.

● To disengage the timer, press ä (TIMER) again.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY"

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (☞ pg. 18).

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HR-S9500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart AV1 OUT switchBack of TV Mains outletBack of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayBefore performing Video Plus+ Timer Programming Video Plus+ Timer ProgrammingPress Prog Correct numberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Playback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Switch SignalSatellite Receiver Unit Rear panel AV1 OUTSelect AV2 Select Mode Access Mode SET ScreenEngage Auto Satellite Prog REC Mode Before performing the following stepsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder TV Receiver AV2 Select SettingYour recorder Quality S-VHS picturesPrepare for Editing Access R.A. Edit ScreenLoad Source Cassette Start Source PlaybackLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Engage Insert EditingStart Editing Start Dubbing Engage Audio DubbingEND Audio Dubbing Audio OUTAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal SET Jlip ID NumberAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerNtsc Playback Repeat PlaybackRetake Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenEnter NEW Channel Storing Channels ManuallyInformation Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersConnect the mains power cord TroubleshootingNo power is applied to the recorder Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgRear View Audio OUT L/R Connectors enableRemote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x
Top Page Image Contents